Porsche Boxster Short Shift Kit (SSK) Installation and Shift Bushing Replacement - 986 / 987 (1997-08)

Applicable Models:

Porsche 987 Cayman S (2006-12)

Project Time: 3 hours
Tab: $150 to $350
Talent
Tools:

Parts Required: Short Shifter Kit (SSK)
Performance Gain: Shorter Shift throws
Complementary Modification: Replace your shifter cables

One of the most popular additions to the Boxster is the installation of a short shift kit.

The kit shortens the length of throw on the stock shifter, theoretically giving you the ability to shift faster. Installation is a moderate task, and should only take the better part of an afternoon.

For the purpose of this project, I chose the Porsche factory short shift kit, which is nearly identical to others on the market (B&M supposedly manufactures the kit for Porsche). Both are available from PelicanParts.com.

The factory kit is shown in Figure 2. It comes complete with everything that you need to replace your shift lever, and replace many of the shift bushings that have a tendency to wear out. Specifically, this kit contains Delrin bushings for the shifter arm and shift lever. The kit is very well constructed and all of the parts fit together with very tight tolerances.

The process of installing the short shift kit involves basically swapping out the shift lever with the old one and installing the new bushings. Follow the steps shown in Photos 1 through 10 to remove the shifter and install the kit. When you have reinstalled the kit into the car and reattached the cables, be sure to test the shifter through all gears. Only when you have confirmed the shifter is working properly should you reinstall the center console.

It took a short while (no pun intended) for me to get used to the new short shift kit. At first, I didn't really care for it, but after driving the car with it installed, I didn't want to go back to the standard shifter. If you're not sure about whether you'll like the short feel, I suggest that you drive someone else's car that has a short shifter installed. The procedure to remove the kit takes as long as the one to install it, so if you're not sure, then try it out beforehand.

On a side note, many people install short shift kits in their cars thinking that it will fix problems that they are having with their transmission. This will not solve any problems, and will in most cases make a poorly shifting car shift even worse. The reason for this is that with the short shift kit, the torque arm on the shift lever is much shorter, giving you much less 'resolution' on your shifter. It's similar to having a gas pedal that only travels 1 inch over its range instead of 2-3 inches (see Pelican Technical Article: Sprint Booster Installation). You have less precision in how much throttle you want to give the car. In a similar manner, with the short shift kit you will have less precision on where the shift rod is placed. It's a wise idea to tackle the core problems with your transmission (synchros, shift bushings), prior to the installation of the short shift kit (see the other transmission projects in this book).

Shifting Improvements: There may come a time in the ownership of your Boxster when you feel that the shifting performance of the car is not quite what it's supposed to be. Renewing the shifter bushings and the cable ends as detailed in this project are a good first step in ensuring crisp shifting. The other end of the shifter cable can wear too (see Photo 3 of Pelican Technical Article: Transmission Removal). Unfortunately, at this time the only way to renew the transmission-end bushings is to replace the entire cable. Replacement is pretty straightforward - it involves disconnecting the cable from the shifter, and then feeding it through the engine compartment to the transmission. On some cars, excessive deterioration of the engine or transmission mounts can cause erratic shifting. This is less of an issue with a cable-driven shifter like the Boxster, but crisp, firm mounts do help overall performance. See Project 10 and Project 36 for complete instructions on replacing the engine and transmission mounts.

Hot tip

If you wish to renew your shifter without installing the short shift, just use the improved bushings

Wayne R. Dempsey, Co-Founder & DIY Expert

Project Photos

Figure 1 Begin by unclipping the shifter boot from the rear and lift it up (inset). To remove the shifter knob some cars use a set screw, and some require you to twist the lower collar 90° and then lift to remove. Remove your old knob by simply pulling upwards on it: be careful not to accidentally smack yourself in the face!

Figure 2 Shown here is the Porsche factory short shift kit. The kit consists of a metal shifter a set of improved bushings and aluminum bushing carriers, and associated mounting hardware.

Figure 3 Shown here are the various steps required to remove the center console. Remove front retaining screw, located under the shifter boot Pull off side cover (it snaps off) and remove lower screw (green arrow) Pull off the front lower console cover (red arrow) Remove the coin tray insert, remove the two screws (yellow arrows), unplug and remove window switch assembly, and remove the additional screw found underneath. Pull back e-brake side cover and remove (pull in the direction of the purple arrow). Also remove the rear storage compartment: there is a screw hidden underneath the small rubber mat inside the compartment, and another screw hidden under the small coin holder (three total in the rear). Unplug any remaining harnesses still attached to the console

Figure 4 This photo shows the center console removed. The purple arrows point to wire harnesses that need to be removed prior to pulling the console from the car.

Figure 5 With the center console removed, you can now work on disconnecting the cables from the shifter. A- Remove the plastic shifter cover, and you will see the cables underneath. B- mark the existing position of the cables with a permanent marker so that you can assemble them back together in the same position as when they came apart. C- Slide the spring-loaded retainers towards the front of the car and release the cable from its holder. D- Unclip the shift cables from the rear of the shifter housing and place them off to the side. Finally, unscrew the shifter housing from the floor and remove from the car.

Figure 6 The stock shifter uses a square bushing that rides in the side cam piece (red arrow). The new short shifter uses a metal ball instead: lubricate this ball prior to assembling it into the shifter. To remove the old stock bushings, use a razor blade and chip away at the edges of the bushings. When the edges have been removed, slide the bushing out of the bore and remove the stock shifter. If you are reusing the cable-end, pop it off of the old shifter and install it onto the new one (see Figure 9).

Figure 7 The new bushings are installed onto the aluminum cylinders located on either side of the shifter. Place the washer in-between the bushing and the bottom of the cylinder. Place the bushing on the shifter shaft, push it in towards the shifter (the direction of the purple arrow) and then fasten it in place using the circlip (yellow arrow, lower left). The circlip goes on the inside of the shifter housing to hold the metal housing from falling out in the direction opposite of the purple arrow (see Figure 9). Be sure to pre-lubricate the bushing prior to assembly (upper left).

Figure 8 Reduce the end play in the shifter by turning the set screw with a hex driver. Turn the set screw until it's tight, and then back it off about 1/4 to 1/2 turn. Lock it in place with the jam nut to secure the assembly. The set screw and jam nut can be installed on either side of the shifter.

Figure 9 I recommend using new cable ends (yellow arrow) when refurbishing your shifter: they will aid in keeping a crisp, reliable feel in your shifter. Lubricate the ball end of the shifter with some white lithium grease prior to installing the cable end. You may have to use some significant force to get the cable end attached: use a hammer to tap it on if necessary.

Figure 10 Here is the shifter assembly, completely upgraded with the new factory short shift kit and the improved bushings. The two purple arrows point to the location of the two installed circlips. Reinstall the kit back into the car, reversing what you had done previously. Use plenty of grease on all the bushings and pivot points.

Figure 11 Replacement bushings for the stock shifter are not available separately: you have to purchase a whole new shifter, at a cost of about $200! Fortunately, the short shift kit contains a set of improved bushings that can also be used with the stock shifter. If you wish to keep your stock shifter and renew the feel in your shifter, then I recommend picking up a set of these improved bushings. One bushing kit is shown in the inset (two required).

Comments and Suggestions

Brian

July 5, 2024

So ..... do you have or can you provide more detailed information on the Upgraded Shifter Bushings you mentioned in Figure 11 above????