Pelican Parts
Parts Catalog Accessories Catalog How To Articles Pelican Tech Forums
Call Pelican Parts at 888-280-7799
- Back to Catalog -
911 Engine/Transmission Jack Adapter
911 Engine/Transmission Jack Adapter (1984-98)
911 Engine Only Jack Adapter
Porsche 911 Engine Lift Bar Tool
Jack Pad
Jack Stands
AC Hydraulic Jacks
Lug Nut Soft Socket
Lug Nut Torque Socket Set
Porsche Engine Rebuild Stand
Engine Stand for Water-Cooled Engines
Engine Stand Adapter Ring
Engine Yoke Securing Nuts
12-Point/12mm Flywheel Socket
Heavy Duty Flywheel Lock
Oil Filter Wrenches
Drain Plug Removal Tool
Transmission Drain Plug Removal Tool
Smart Racing Products Alignment Tools
Hub/Bearing Extractor and Installer Kit
Oil Seal Installation Tools
Secondary Air Injection (SAI) Maintenance DVD
Secondary Air Injection (SAI) Maintenance Tool Kit
Mechanical Tensioner/Tool
Cylinder Holding Tool
Top Dead Center Indicator
Leakdown/Compression Gauge Adapter
Metric Dial Indicator Gauge
Cam Nut Tool
Camshaft Tools
Camshaft Sprocket Alignment Tool
Valve Spring Tools
911 Valve Adjustment Tool
Valve Adjustment Tool with Loop Handle
Exhaust Head Stud Repair Kit
Crankshaft Holder
Circlip Injector Tool
Transmission Synchro Tools
Shift Fork Jig
Pulley Wrench Tools
Fuel Injection Tools
Mechanical Injection Pump Tools
CIS Fuel Enrichment Wrench
C.I.S. K-Jetronic Fuel Injection Tester
Ball Joint Tools
Tie Rod Tools
Factory Timing Belt Tensioning Tool
Timing Sprocket Registration Pin Puller
944/968 Flywheel Lock
Float Gauge
Allen Head Tools
CV Bolt Removal Tool
Magnetic Box "V" Wrench (17mm)
Suspension Alignment Tools
Ride Height Wrench
Trailing Arm Height Adjuster
Elephant Racing Spring Plate Bushing Removal Tool
Extraction Tools
Spanner Wrench Set
32 MM Oil Line Wrench
36 MM Oil Line Wrench
Clutch Alignment Tool
Disassembly Tools
Factory Air Pump
Custom Service Cover
Durametric Software Diagnostic Tool for Porsche
AutoEnginuity Complete OBDII Diagnostic Tool
ScanTool Software Expansions
Air/Fuel Ratio Meter
WEGO IV Wide-Band Air/Fuel Ratio Tuning Aid
Innovate Motorsports LM-2
Redline Detection Smoke Pro
Airlift Cooling System Tool Kit
Radio Removal Tools
Pelican Engine Rebuild Super Tool Kits
- Back to Catalog -
Home >  Porsche Catalog >   Porsche Tools  
Porsche Tools - Page 8

Fuel Injection Tools

Mechanical Injection Pump Tools
The Adjustment Driver Kit contains three tools specifically designed to help you adjust the mechanical injection pump for performance or emissions tuning. One tool is used to remove a plug on the pump accessed through the fan. The other two are used for actually adjusting the pump's settings.


Mechanical Injection Pump Adjustment Driver Kit, 911 (1969-73)    [More Info]

CIS Fuel Enrichment Wrench
Adjusting your CIS injection will nearly be impossible without this handy tool. Made from hardened steel for many years of service. NOTE: This is a generic wrench and may need to be cut down to fit your particular application.


CIS Fuel Enrichment Wrench    [More Info]

No Longer Available 
C.I.S. K-Jetronic Fuel Injection Tester
You can do it all with this Fuel Injection Tester. Works on all Continuous Injection System (CIS) units on late-model European cars. Complete with all adapters and hook-ups.


C.I.S. K-Jetronic Fuel Injection Tester with Case    [More Info]

No Longer Available 

Ball Joint Tools

The large castellated nut that secures the ball joint to the A-arm (901-341-425-00) should be removed either with a chisel or an impact hammer due to the incredible amount of force necessary to budge it free. This will normally render the old nut useless, and require it to be replaced along with the ball joint. This nut also requires a special tool for installation since it needs to be properly torqued to a whopping 184 ft-lbs. This specially made socket uses a 1/2" drive and is the only tool for the job.


Ball Joint Pin Wrench Socket, 1/2 Drive, NOTE: For INSTALLATION ONLY, 911 (1965-89), 914 All, 912    [More Info]


Ball Joint Separating Tool, All, except 356    [More Info]


Tie Rod Tools


Tie Rod End Puller, 911 (1965-89), 914 All, 912    [More Info]

No Longer Available 

Factory Timing Belt Tensioning Tool

The tools below are all that are needed to take the guess work out of properly adjusting your timing and balance shaft. The belts must be done every 15,000 miles and doing so is the only way to ensure long engine life. The Tensioning tool is Made in Germany, same tool the factory technicians use. Comes with a factory 2 year Limited Warranty.944 Balance Shaft Locking Bar - The balance shaft locking bar is used during the timing belt replacement process on 944s. It is designed to keep the balance shaft sprocket from turning while removing/replacing the retaining bolt.Timing Belt Adjusting Tool-This specially designed tool makes adjusting the timing belt a snap. Balance Shaft Belt Gauge - This tool has also proved invaluable to properly adjust the roller for the balance shaft toothed belt.


Factory Timing Belt Tensioning Tool, 944 (3/1983-89), 924S/944S (1987-88), 944S2 (1989-91), 944 Turbo (1986-89), 968 (1992-95)    [More Info]



Aftermarket 944 Balance Shaft Locking Bar    [More Info]



Factory 944 Balance Shaft Locking Bar    [More Info]



Timing Belt Adjusting Tool (for 24mm rollers), 944 (3/1983-89), 924S/944S (1987-88), 944S2 (1989-91), 944 Turbo (1986-89)
   Brand: Genuine Porsche    [More Info]



Timing Belt Adjusting Tool (for 27mm rollers), 924, 944, 944 Turbo, and 968 with the later style 27mm rollers     [More Info]



Calibration Bar    [More Info]



Balance Shaft Belt Gauge    [More Info]


  Page 8 of 13  <12345678910111213>


About Us
Pelican Parts, LLC
1600 240th Street
Harbor City, CA 90710
Order Online or Call:
Sign Up for Pelican Pit Stop News & Special Offers
Copyright 2016 Pelican Parts, LLC
DMCA Registered Agent Contact Page

Page last updated: Tue 3/20/2018 01:15:25 AM