Pelican Parts
BMW Parts Catalog Accessories Catalog BMW How To Articles BMW Tech Forums
Call Pelican Parts at 888-280-7799
1987 BMW 325e Base Coupe
BMW Home > 1987 BMW 325e Base Coupe > Suspension & SteeringAxles, Bearings & Differential 

Axles, Bearings & Differential

- Page 2

CV Joint Removal Tool
Axle Boot Clamp Pliers - 3/8" Drive  
[ More Info ]

Note: For installation of crimp-type axle boot clamps, Ergonomic 2-component handle. 178 mm length.

Brand Rating

Axle Boot Clamp Pliers  
[ More Info ]

Note: With lug holding-down device, Nickel Plated, 230 mm length.

Brand Rating

Axle Boot Clamp Pliers - 3/8" Drive  
[ More Info ]

Note: For installation of crimp-type axle boot clamps.

Assenmacher Tools (AST)
Brand Rating

Avoid stripping your bolt heads and spending wasted hours cutting and grinding them off by using this special tool to easily remove those pesky CV joint bolts. This tool is for use with 12-point star-shaped bolts only. Please make sure to check your bolts before ordering. It's common for previous owners to replace the 12-point star shaped bolts with more standard allen head bolts instead. Although the 12-point pattern allows you to get a better grip on the bolts (with the correct tool), and apply the high torque that the bolts require, previous owners may have stripped out these bolt heads by attempting to use a torx or hex driver instead of the proper tool. A word of caution here - these other tools MAY work, but if they strip the bolt head, then you are in for an entire afternoon of grinding it off the next time it's replaced.

TIP: Spray the bolts down with WD-40 or Liquid Wrench first to loosen the dirt and debris in the bolt head, then scrape out any dirt that may be left. With the socket on a 6" extension, slip the tool into the bolt head and give it a gentle rap on the end with a mallet to seat it firmly. Following this simple procedure will hopefully avoid you from stripping any CV bolts.

CV Joint Parts

If you are hearing a "clicking" or "clunking" sound coming from under your car there is a good chance your CV joints are starting to go bad. CV (constant velocity) joints are responsible for providing a direct link between the axles and the wheels. They allow the power to be distributed evenly throughout varying degrees of rotation and can fail. One of things you can do to prevent their failure is to inspect the boots that cover the joints and make sure they are not ripped or torn. CV joints should be disassembled, inspected and repacked in the appropriate grease as needed. Pelican offers all the parts necessary to rebuild your constant velocity joints.
Axle Boot Kit for C/V Joint (Left or Right Rear Outer)

Axle Boot Kit for C/V Joint (Left or Right Rear Inner)

Differential Parts

This section contains the parts necessary to service or repair your differential.

Differential Drain Plug with O-Ring (22 X 1.5 mm)

Differential Drain Plug Wrench - 14 mm Allen, 17 mm Box  
[ More Info ]

Note: Slim design to remove and replace the differential drain and fill plugs on many BMW models,

Brand Rating

Lock Plate for Output Flange Nut

Differential Mount - Differential Cover - Powerflex  
[ More Info ]

Note: Shore 80A purple polyurethane, suitable for street performance use,

Brand Rating

Differential Mount - Differential Cover

BMW Home  >  1987 BMW 325e Base Coupe > Suspension & Steering  >  Axles, Bearings & Differential 

  Page 2 of 8  <12345678>

Browse Axles, Bearings & Differential for all 3-Series E30 (1983-1991) vehicles

Page last updated: Wed 3/14/2018 02:31:13 AM
About Us
Pelican Parts, LLC
1600 240th Street
Harbor City, CA 90710
Order Online or Call:
Sign Up for Pelican Pit Stop News & Special Offers

Close this window