Parts Catalog Accessories Catalog Tech Info Tech Forums
 
  Search our site:    
View Recent Cars  |   Cart  | Project List | Order Status | Help    
 >  >
Porsche 911 Carrera Master Cylinder Replacement
 
Bookmark and Share

Pelican Technical Article:

Porsche 911 Carrera Master Cylinder Replacement

Time:

3 hours3 hrs

Tab:

$100 to $300

Talent:

***

Tools:

Brake bleeder, torque wrench

Applicable Models:

Porsche 996 Carrera models (1999-05)
Porsche 996 Turbo, GT2, GT3 (2001-05)
Porsche 997 Carrera models (2005-12)
Porsche 997 Turbo, GT2, GT3 (2007-13)

Parts Required:

Master cylinder, brake fluid

Hot Tip:

Make sure that you keep all brake fluid away from your paint

Performance Gain:

Better braking, no more leaky master cylinders

Complementary Modification:

Replace brake booster, install stainless steel brake lines

Without a doubt, your brakes are one of the most important systems on the car. The heart of the brake system is the master cylinder, which controls the hydraulic pressure of the entire system. Unfortunately, over many years, the master cylinder has a tendency to wear out and leak. The leakage can occur internally or externally, resulting in a weakened braking system. If you have any problems with your brakes, and you think that it's related to the master cylinder, you should probably replace it.

The master cylinder is located in the front trunk area, on the driver's side, under a large plastic panel. To gain access to the master cylinder, you need to remove this panel. Begin by pulling up the hood seal and removing the three Phillips head screws located on the top of the panel. Rotate the slotted plug on the lower front corner of the panel and remove it, disconnecting the trunk lamp harness as you go. Now, remove the strainer from the brake fluid reservoir and then remove brake fluid using a turkey baster or a suction device. Or, you can also bleed the entire system of fluid by emptying the brake fluid out of one of the caliper bleed screws (see Pelican Technical Article: Bleeding Porsche 911 Carrera Brakes). Be aware that some residual fluid will remain inside of the master cylinder and that brake fluid is very damaging to paint. Disconnect the brake fluid level sensor from the reservoir.

Now you need to remove the reservoir. Disconnect the clutch master cylinder supply line--you will need to push in the press-fit connector with a small wrench carefully as you pull on the line. If you are not replacing the reservoir, then I recommend just leaving it connected and pushing the reservoir off to the side. Simply pull up on the reservoir to remove it from the O-rings that seal it to the master cylinder.

With the reservoir disconnected, place a towel under the master cylinder and disconnect the two brake line fittings. As with the installation of new flexible brake lines, it is very important not to strip out the fittings on the lines. You should always use a flare-nut wrench to remove the fittings from the master cylinder. See Project 54 for more details. It's also a wise idea to spray the area with some WD-40 or other lubricant if the lines seem to be heavily corroded. Cap the open brake lines with plastic covers to prevent brake fluid leakage. Remove the two nuts that attach the master cylinder to the brake booster, and you should be able to remove the master cylinder.

Installation is basically the reverse of removal. If you are replacing your ABS control unit or your brake booster, then at this point, see Project 57 for instructions on how to accomplish that task.

When the master cylinder is reinstalled, it's time to bleed your brake system. You may want to dry bleed the master cylinder on the bench in order to prime it before you start the install. For more information on bleeding your brakes, see Pelican Technical Article: Bleeding Porsche 911 Carrera Brakes. Following the bleeding of the brakes, reassemble all the surrounding parts in the trunk that you have disassembled, and make sure that everything is tightened. Reinstall all the carpets and fasteners.

When you are ready to drive the car, make sure that you test the brakes beforehand. Don't drive near other cars, and prepare to use the emergency brake if necessary. It's probably a wise idea to bleed the brakes again a few days after you install the new master cylinder to make sure that you have gotten all of the air out of the brake system.

The master cylinder is hidden behind a plastic panel located in the front trunk.
Figure 1

The master cylinder is hidden behind a plastic panel located in the front trunk. Remove the large plastic screw that hold the trunk liner down (blue arrow) and the three small Philips head screws(yellow arrows), and pull the liner out. There is a front trunk lamp (red arrow) embedded in the liner--remember to unplug the harness connected to this lamp.

Here's what you will see when you remove the front trunk liner.
Figure 2

Here's what you will see when you remove the front trunk liner. The purple arrow shows the vacuum-powered brake booster, which is the muscle behind the power-brake system. The orange arrow shows the brake fluid reservoir, which supplies hydraulic fluid to both the brake and clutch systems. The red arrow shows the ABS hydraulic control unit. The white arrow points to the master cylinder. The yellow arrow indicates the connection for the reservoir level sensor, and the green arrow shows the vacuum line that powers the brake booster. Finally, the light blue arrow shows the electrical connector that plugs into the front trunk lamp.

Shown here is a close-up of the master cylinder connections.
Figure 3

Shown here is a close-up of the master cylinder connections. First, empty out the reservoir, and then disconnect the clutch system supply tube (green arrow). Then, disconnect the two brake lines attached to the side of the master cylinder. Only use a flare-nut wrench (blue arrow, inset) as you otherwise may end up damaging the connectors on the lines.

With the brake lines disconnected and the reservoir removed from the top of the master cylinder, remove the two nuts that fasten the master cylinder to the brake booster (yellow arrows).
Figure 4

With the brake lines disconnected and the reservoir removed from the top of the master cylinder, remove the two nuts that fasten the master cylinder to the brake booster (yellow arrows).

Shown here is a brand new master cylinder with five protective caps attached.
Figure 5

Shown here is a brand new master cylinder with five protective caps attached. Carefully remove the caps right before you are ready to install the unit and/or the brake lines.

Bookmark and Share
Comments and Suggestions:
987 Cayman Comments: Is there a certain torque we should use for connecting the master cylinder back to the booster? and I'm assuming just hand tight for the nuts that attach the lines back to the brake master cylinder?
May 15, 2014
  Followup from the Pelican Staff: Yes there is. I do not have the torque handy. I would grab a repair manual. It will have the procedure, special tools and torque specs.
- Nick at Pelican Parts
 

  Search our site:    

View Cart & CheckOut | Project List | Order Status |  Help    

 

[Home] [Customer Service] [Shopping Cart] [Project/Wish List]
  [Privacy Statement]  [Contact Us] [About Us] [Shipping] [Careers]

Copyright © Pelican Parts Inc. -    DMCA Registered Agent Contact Page

Page last updated: Mon 12/5/2016 02:31:26 AM