Pelican Parts
Porsche Parts Catalog Accessories Catalog Porsche How To Articles Porsche Tech Forums
Call Pelican Parts at 888-280-7799
View Recent Cars  |Shopping Cart Cart | Project List | Order Status | Help

Pelican Technical Article:

Firewall Removal

Steve Vernon

Time:

2 hours2 hrs

Tab:

$0

Talent:

***

Tools:

Philips, Flathead screwdriver, 5mm Allen, 10mm socket, 13mm wrench

Applicable Models:

Porsche 993 Carrera (1995-98)
Porsche 993 Carrera 4 (1995-98)
Porsche 993 Carrera 4S (1996-98)
Porsche 993 Carrera S (1998)
Porsche 993 Targa (1996-98)
Porsche 993 Turbo (1996-97)

Parts Required:

Control board

Hot Tip:

Get a friend to help lift it out

Performance Gain:

Access to the systems behind it

Complementary Modification:

Check your fuses and relays

Things are packed pretty tight in modern Porsches and that includes the 993. One of the important questions you will ask yourself when you start working on your Porsche is: how the heck do they expect me to get at that part without removing this part? The truth of the matter is that a lot of times you do need to move other parts, systems or components out of the way to change something and then re-install them. Many first time DIY'ers get frustrated working in really tight spaces or end up damaging something they are not working on just to "save the time" of not having to remove other components. If you are going to work on your 993, get in the habit of moving things out of the way and giving yourself all the room you can to work; in the end you will end up saving time and money.

The firewall is one of the parts that needs to be moved out of the way for several jobs including changing your blower motors and removing the suitcase to change your evaporator, etc. This article will show you how to safely remove the firewall but we do recommend getting a friend to help lift it out the first time you do it, not because it is heavy but because you do not want to scratch the paint.

Over the years your car may have been serviced by multiple people including previous owners and this can lead to parts replaced with different size fasteners and hardware. The sizes of the nuts and bolts we give may be different from what you have so be prepared with different size sockets and wrenches.

You are going to be working with the main electrical control board which houses the main fuse and relay panel.
Figure 1

You are going to be working with the main electrical control board which houses the main fuse and relay panel. Before you begin you must disconnect the ground strap from the post and the battery and place it where it cannot accidentally come in contact with the post while working (red arrow).

The firewall is located behind the gas tank and in front of the HVAC suite case.
Figure 2

The firewall is located behind the gas tank and in front of the HVAC "suite case". It has a rubber weather sealing gasket along the top of it (red arrow).

Begin by removing the weather seal by simply pulling it up and off (red arrow).
Figure 3

Begin by removing the weather seal by simply pulling it up and off (red arrow).

Use a short Philips head screwdriver and remove the two screws (red arrows) holding the shroud in place and remove the shroud.
Figure 4

Use a short Philips head screwdriver and remove the two screws (red arrows) holding the shroud in place and remove the shroud.

Remove the electrical connection for the blower motor regulator by squeezing in the clips and pulling it up (yellow arrows) then gently pry the wiring harness connector from the back of the regulator (red arrow).
Figure 5

Remove the electrical connection for the blower motor regulator by squeezing in the clips and pulling it up (yellow arrows) then gently pry the wiring harness connector from the back of the regulator (red arrow). The regulator is attached to the heat sink plate and this is mounted to the firewall and will come out with the firewall.

With the weather stripping off the firewall (red arrow) use a Philips head screwdriver and remove the three screws (yellow arrows) and remove the corner plate between the control panel housing and fender.
Figure 6

With the weather stripping off the firewall (red arrow) use a Philips head screwdriver and remove the three screws (yellow arrows) and remove the corner plate between the control panel housing and fender.

Unscrew the plastic retaining knob in the upper corner (red arrow).
Figure 7

Unscrew the plastic retaining knob in the upper corner (red arrow).

Using a 5mm Allen remove the single bolt in the front corner.
Figure 8

Using a 5mm Allen remove the single bolt in the front corner.

Do not lose the plastic shim that goes between the panel and housing.
Figure 9

Do not lose the plastic shim that goes between the panel and housing.

You can now lift the panel, fuses, and relays and wiring harness up and out from the housing.
Figure 10

You can now lift the panel, fuses, and relays and wiring harness up and out from the housing. Place a shop towel down between the panel and fender and tie the panel out of the way.

You're now looking at the fuse panel housing which is attached to the fire wall (red arrow) and the fuel expansion tank (yellow arrow); you do not need to remove the expansion tank to remove the firewall.
Figure 11

You're now looking at the fuse panel housing which is attached to the fire wall (red arrow) and the fuel expansion tank (yellow arrow); you do not need to remove the expansion tank to remove the firewall.

Use a 10mm socket or wrench and remove the bolt holding the bottom of the fuse panel housing to the chassis (red arrow).
Figure 12

Use a 10mm socket or wrench and remove the bolt holding the bottom of the fuse panel housing to the chassis (red arrow).

Next use a Philips head screwdriver and remove the screws holding the housing to the inside of the fender.
Figure 13

Next use a Philips head screwdriver and remove the screws holding the housing to the inside of the fender.

Move to the left side of the firewall and remove the top two Philips head screws and loosen the lower one.
Figure 14

Move to the left side of the firewall and remove the top two Philips head screws and loosen the lower one.

It is a tight fit and having a Philips head ratchet really helps.
Figure 15

It is a tight fit and having a Philips head ratchet really helps.

With the top two screws removed and the lower screw loosened you can remove the plate that allows you to remove the firewall without completely removing the lower screw.
Figure 16

With the top two screws removed and the lower screw loosened you can remove the plate that allows you to remove the firewall without completely removing the lower screw.

If this is the first time you have done this it is a really good idea to get a friend to help you lift it out as even though the piece is not heavy you do not want to scratch anything.
Figure 17

If this is the first time you have done this it is a really good idea to get a friend to help you lift it out as even though the piece is not heavy you do not want to scratch anything. It lifts straight up and out (red arrow).

Here is a picture of the firewall out of the car.
Figure 18

Here is a picture of the firewall out of the car. You can see the heat sink blower motor regulator attached on the back. Use care with this piece, you do not want to damage it as it is very expensive to replace. Installation is the reverse of removal.


QUICK LINKS
About Us
Careers
Pelican Parts, LLC
1600 240th Street
Harbor City, CA 90710
Order Online or Call:
888-280-7799
CONNECT WITH US
NEWSLETTER
Sign Up for Pelican Pit Stop News & Special Offers
Page last updated: Sun 12/10/2017 03:12:28 AM