Mercedes-Benz Parts Catalog Mercedes-Benz Accessories Catalog Mercedes-Benz Technical Articles Mercedes-Benz Tech Forums
 
Follow Pelican Parts on Facebook Follow Pelican Parts on Twitter Follow Pelican Parts on Instagram Follow Pelican Parts on YouTube Follow Pelican Parts on Pinterest Follow Pelican Parts on Tumblr
  Search our site:    
View Recent Cars  |   Cart  | Project List | Order Status | Help    
Bookmark and Share

Pelican Technical Article:

Bleeding Brakes

Steve Vernon

Time:

2 hours2 hrs

Tab:

$20

Talent:

**

Applicable Models:

Mercedes-Benz C250 (2012-14)
Mercedes-Benz C300 (2008-14)
Mercedes-Benz C350 (2008-14)

Parts Required:

3+ quarts of brake fluid

Hot Tip:

Make sure to get all the air out from the system

Performance Gain:

Quicker, firmer stopping

Complementary Modification:

Rebuild brake calipers

Bleeding brakes is not one of my personal favorite jobs. There seems to be a bit of black magic involved with the bleeding process. Sometimes it will work perfectly, and then other times it seems like you end up with a lot of air in your system. The best strategy to follow when bleeding your brakes is to repeat the procedure several times in order to make sure that you have removed all the trapped air from the system.

The basic system can be bled using the traditional method. There are currently two popular methods of bleeding the brake system: pressure bleeding and vacuum bleeding. Pressure bleeding uses a reservoir of brake fluid that has a positive air pressure force placed on the opposite side of the fluid, which forces it into the brake system. Vacuum bleeding is where you fill the reservoir and then apply a vacuum at the bleeder nipple to pull fluid through the system.

The method that I've come up with combines the first method described above and yet another third finishing method. I advocate bleeding the system with the pressure bleeder and then using a family member to depress the brake pedal to free up any trapped air in the system. If your esteemed assistant really owes you a favor, you will be the one depressing on the pedal, and they can spill brake fluid all over themselves.

The first step in bleeding your brakes is to jack up the car and remove all four wheels. The next step is to fill the system with brake fluid. I recommend using different colored brake fluid, in order to determine when fresh fluid has been flushed through the entire system. One of my favorite tools for pressure bleeding is the Motive Products Bleeder.

The system has a hand pump that you can use to pressurize the brake fluid to just about any pressure. A small gauge on the front of the brake fluid reservoir indicates the pressure of the brake fluid inside. The very large reservoir can hold about two quarts of brake fluid--more than enough for most brake flushing and bleeding jobs. The bleeder kit is a very useful and cost-effective tool to have in your collection.

The system bleeds by pressurizing a bottle filled with brake fluid from air from an internal hand pump. The procedure is to add fluid, attach the bleeder to the top of the reservoir cap, and pump up the bleeder bottle to about 15-20 psi using the hand pump. This will pressurize the system. Check to make sure that there are no leaks around the bleeder or where it attaches to the top of the master cylinder reservoir.

Now start bleeding the system. Start with the right rear caliper, the one that's located furthest away from the master cylinder. Bleed the right rear caliper by attaching a hose to the bleed nipple, placing it in a jar, and then opening the valve by turning the bleeder nipple counter-clockwise with an 11mm wrench. Let the fluid flow out until there are no more bubbles. If you don't have a pressure bleeder system, you need to find someone to press on the pedal repeatedly to force fluid through the system.

Another solution is to get a check valve and place it on the nipple while you depress the pedal. This will work for getting fluid into the system but you will still need a second person for the final step to make sure you have bled the system completely.

When no more air bubbles come out, move to the next caliper. Bleed them in this order: right rear caliper, left rear caliper, right front caliper, left front caliper. Bleeding in this order will minimize the amount of air that gets into the system.

Repeat the process until you can no longer see any air bubbles coming out of any of the calipers. Make sure that you don't run out of brake fluid in your reservoir or you will have to start over again. It is wise to start out with about a 1/2 gallon of brake fluid in the pressure bleeder and another 1/2 gallon on the shelf in reserve. Depending upon your car, and the mistakes you may make, I recommend having an ample supply. Also, only use new brake fluid from a sealed can. Brake fluid is hydroscopic, meaning that it attracts water and water vapor, which diminishes its performance. Brake fluid containers left exposed to air will have the fluid inside compromised after a short period of time.

If you had to replace the master cylinder, or if the system needs a large amount of fluid, then supplement the bleeding process by opening up the right rear nipple and then pressing down on the brake pedal two or three times. Slowly release the pedal. Repeat for the other three corners of the car.

During the bleeding process, it's very easy to forget to check your master cylinder reservoir. As you are removing fluid from the calipers, it will be emptying the master cylinder reservoir. If the reservoir goes empty, then you will most certainly add some air bubbles in to the system, and you will have to start all over. Keep an eye on the fluid level and don't forget to refill it. Make sure that you always put the cap back on the reservoir. If the cap is off, then brake fluid may splash out and damage your paint when the brake pedal is released. If you are using a pressure bleeder system, make sure that you often check the level of brake fluid in the bleeder reservoir so that it doesn't accidentally run dry.

Now, make sure that all the bleeder valves are closed tightly. Disconnect the pressure system from the reservoir. Follow the directions carefully, and never loosen the reservoir cap when it is under pressure. Now, get your family member to repeatedly press the brake pedal down at least five times, and then hold it down. Take care not to push the brake pedal all the way to the floor, as you can actually damage the master cylinder by driving the piston into an usually unused portion of the master cylinder and damaging the seals. Then open the bleeder valve on the right rear caliper. The system should lose pressure, and the pedal should sink to the floor.

When the fluid stops coming out of the bleeder valve, close the valve, and then tell your family member to let their foot off of the pedal. Do not let them take their foot off until you have completely closed the valve, or it will suck air back into the system. Repeat this entire procedure at least three times on each caliper in the same order as described previously.

I recommend that you use this procedure as a final step, even if you are vacuum bleeding or pressure bleeding. The high force associated with the pressure from the brake pedal can help free air and debris in the system. If the brake fluid doesn't exit the nipple quickly, then you might have a clog in your lines. Brake fluid that simply oozes out of the bleed nipple slowly is a clear indication that your rubber lines might be clogged and constricted. Don't ignore these warning signs--replace the brake lines while you are working in this area.

Now, let the car sit for about 10 minutes. Repeat the bleeding process at each corner. The pedal should now feel pretty stiff. If the pedal still feels spongy, make sure that you have the proper adjustment on your rear calipers or drum shoes. Also, you may need a new master cylinder, have a leaky caliper, or have old spongy flexible brake lines.

Another important thing to remember is that brake fluid kills--paint jobs, that is. Brake fluid spilled on paint will permanently mar the surface, so be very careful not to touch the car if you have it on your hands and clothing. This, of course, is easier said than done--don't bleed the system in a tight garage.

The probability of spilling on yourself and then leaning against your car is too great. Rubber gloves help protect yourself from getting it on your hands and your paint. If you do get a spot on your paint, make sure that you blot it with a paper towel--don't wipe or smear it, then quickly rinse with plenty of water. It's also important not to try to clean it off with any chemical or other cleaning solutions.

There are few little tricks that you can use when changing your brake fluid.
Figure 1

There are few little tricks that you can use when changing your brake fluid. It's a smart idea to use a different colored fluid and then bleed the brakes. Make sure to check with your owner's manual, and only use the approved brake fluid for your system. Use of an improper or non-approved brake fluid can result in your brake system not functioning properly. Shown here is the Motive Products Power Bleeder (red arrow) attached to the reservoir (yellow arrow) by its hose and cap. Pour the approved brake fluid into the bleeder and attach the cap. Slowly pressurize the system using the hand pump on the Power Bleeder until you have around 15-20 psi. Make sure everything is sealed up tight and that there are not any leaks in the system.

Make sure you use the proper tool for the job, and that tool is a flared nut wrench (yellow arrow).
Figure 2

Make sure you use the proper tool for the job, and that tool is a flared nut wrench (yellow arrow). The flared nut wrench will grab six sides of the bleed nipple and prevent it from stripping. The nipples are small, made from a softer metal and can round off easily if you do not use the flared nut wrench. Remove the protective cap from the nipple (red arrow), and attach a clear drain tube or hose to the end of it.

Open the bleed nipple by loosening it in the caliper by about a quarter of a turn (yellow arrow).
Figure 3

Open the bleed nipple by loosening it in the caliper by about a quarter of a turn (yellow arrow). Let the brake fluid run out of the caliper until no more bubbles appear. You should use a clear tube (red arrow) so you can see the air bubbles escaping and when they stop. If you are working by yourself beside the catch bottle I always like to have a large drip pan or rubber container underneath my work area. Brake fluid is very messy and will stain or ruin anything it comes in contact with.

Mercedes recommends you flush and replace your brake fluid every two years. Deposits and debris can build up in the lines over time and decrease the efficiency of your brakes. Regular bleeding of your system can also help you spot brake problems that you wouldn't necessarily notice simply by driving the car. Also, never reuse brake fluid. Always use new, fresh fluid. In addition, don't use brake fluid that has come from an open can that has been sitting on the shelf or sitting in your Power Bleeder for a while. The brake fluid has a tendency to absorb moisture when sitting on the shelf. This moisture "boils" out of the brake fluid when you start using the brakes and can result in a spongy pedal.


Bookmark and Share

  Search our site:    

View Cart & CheckOut | Project List | Order Status |  Help    

 

[Home] [Customer Service] [Shopping Cart] [Project/Wish List]
  [Privacy Statement]  [Contact Us] [About Us] [Shipping] [Careers]

Copyright © Pelican Parts Inc. -    DMCA Registered Agent Contact Page

Page last updated: Wed 12/7/2016 02:59:31 AM