Parts Catalog Accessories Catalog Tech Info Tech Forums
 
Follow Pelican Parts on Facebook Follow Pelican Parts on Twitter Follow Pelican Parts on Instagram Follow Pelican Parts on YouTube Follow Pelican Parts on Pinterest Follow Pelican Parts on Tumblr
  Search our site:    
View Recent Cars  |   Cart  | Project List | Order Status | Help    
 >  >
S54 6 Cylinder Engine Throttle Body Actuator Replacement
 
Bookmark and Share

Pelican Technical Article:

S54 6 Cylinder Engine Throttle Body Actuator Replacement

Nick Czerula

Time:

5 hours5 hrs

Tab:

$300

Talent:

*****

Tools:

Set of sockets, flathead, Phillips screwdrivers, boot clamp pliers

Applicable Models:

BMW E46 M3 Coupe/Conv (2006)
BMW Z4 Coupe/Conv (2006)

Parts Required:

Throttle body actuator, actuator rod, intake manifold clamps, seals

Hot Tip:

Work with a cool engine

Performance Gain:

Car will run well

Complementary Modification:

Inspect the intake air ducts and replace if necessary. Replace the air filter.

On the 6-cylinder S54 engine installed in BMW Z4 vehicles, the molded plastic intake manifold or intake plenum mounts between the six individual throttle bodies and the intake air housing. The manifold is designed for maximum volume required for the S54 engine. Depending on the model the S54 is installed in, it will vary slightly, due to engine compartment restrictions. The flow characteristics of the one-piece plastic shell are enhanced by internal funneling cones to direct the intake air to the throttle housings.

The plenum is attached to the throttle housings by rubber sleeves. The S54 uses six individual throttle housings operated by one electronic throttle actuator (EDR). For low engine speed (low load) and idling, intake air is provided by an idle control valve. The valve regulates airflow through an external air distribution pipe to the individual throttle housings.

The digital motor electronics (DME) engine management system in BMW Z4 vehicles with the S54 6-cylinder engine is designed with a drive-by-wire throttle. There is no throttle cable connecting the accelerator pedal to the throttle housing. Instead, potentiometers in the accelerator pedal module (PWG) communicate pedal position directly to the engine control module (ECM). Two separate signals, one signaling pedal position and the other indicating rate of pedal movement, communicate driver demand on the system.

Based on pedal position and movement, the ECM communicates the throttle opening to the throttle bodies at the intake manifold via the EDR. A faulty throttle body actuator can cause a number of problems for the engine, from a check engine light to a rough or surging idle. Before you condemn your EDR, be sure to inspect all the intake air ducts. They should be well-sealed and free from cracks or tears. Check the function of your crankcase breather valve and inspect all the breather hoses. If a breather hose cracks or fails, the air leak can cause a rough idle or engine stalling.

Keep in mind that when your car was serviced before, parts may have been replaced with different size fasteners used in the replacement. The sizes of the nuts and bolts we give may be different from what you have, so be prepared with different size sockets and wrenches.

Protect your eyes, hands and body from fluids, dust and debris while working on your vehicle. If you're working with the electrical system, disconnect the battery before beginning. Always catch fluids in appropriate containers and properly dispose of any fluid waste. Recycle parts, packaging and fluids when possible. Do not work on your vehicle if you feel the task is beyond your ability.

Vehicle models change and evolve, as they grow older, so the vehicle shown in our illustrations may vary slightly from yours. If something seems different, let us know and share your info to help other users. Do you have questions or want to add to the article? Leave a comment below. When leaving a comment, please leave your vehicle information.

Disconnect the negative (-) battery cable. See our tech article on battery connection notes.

Remove the intake manifold. See our tech article on intake manifold removing.

On the 6-cylinder S54 engine installed in BMW Z4 vehicles, the molded plastic intake manifold or intake plenum (green arrow) mounts between the six individual throttle bodies and the intake air housing.
Figure 1

On the 6-cylinder S54 engine installed in BMW Z4 vehicles, the molded plastic intake manifold or intake plenum (green arrow) mounts between the six individual throttle bodies and the intake air housing. The manifold is designed for maximum volume required for the S54 engine. Depending on the model the S54 is installed in, it will vary slightly, due to engine compartment restrictions. The flow characteristics of the one-piece plastic shell are enhanced by internal funneling cones to direct the intake air to the throttle housings. The plenum is attached to the throttle housings by rubber sleeves (red arrows). The S54 uses six individual throttle housings operated by one electronic throttle actuator (EDR). For low engine speed (low load) and idling, intake air is provided by an idle control valve. The valve regulates airflow through an external air distribution pipe to the individual throttle housings.

With the manifold removed, you have clear view of the EDR (red arrow) and the connecting rod (green arrows) to the throttle bodies.
Figure 2

With the manifold removed, you have clear view of the EDR (red arrow) and the connecting rod (green arrows) to the throttle bodies.

Start by rotating the lower connection of the rod off the EDR (red arrow).
Figure 3

Start by rotating the lower connection of the rod off the EDR (red arrow).

Next, disconnect the electrical connector by pressing the wire retainer (red arrow) and pulling it straight off.
Figure 4

Next, disconnect the electrical connector by pressing the wire retainer (red arrow) and pulling it straight off. There is one more electrical connector. You will have to wait until the EDR is removed from the engine to access it.

Start by removing the top two 10mm fasteners.
Figure 5

Start by removing the top two 10mm fasteners. Then loosen the lower fastener all the way (red arrows). The lower fastener will stay in the bore of the EDR as you remove it (green arrow), due to the restricted space caused by the wiring harness junction below it.

Pull the EDR straight off the engine, with the lower fastener still in the mounting bore (red arrow).
Figure 6

Pull the EDR straight off the engine, with the lower fastener still in the mounting bore (red arrow).

Next, disconnect the second electrical connector by pressing the wire retainer (red arrow) and pulling it straight off.
Figure 7

Next, disconnect the second electrical connector by pressing the wire retainer (red arrow) and pulling it straight off.

If replacing yours with a used model, be sure the part numbers match.
Figure 8

If replacing yours with a used model, be sure the part numbers match. Once removed, you can replace the throttle switch (red arrow) separately, if it is faulty.

When installing, reverse the removal directions. To adapt the EDR, turn the ignition key to the ON position for 10 seconds, (do not start engine). Next turn the ignition key to the OFF position for 10 seconds. Start the engine.

Bookmark and Share

  Search our site:    

View Cart & CheckOut | Project List | Order Status |  Help    

 

[Home] [Customer Service] [Shopping Cart] [Privacy Statement]
 [Contact Us] [About Us] [Shipping] [Map to our Location] [Careers]

Copyright © Pelican Parts Inc.

Page last updated: Fri 12/9/2016 02:57:17 AM