Audi Parts Catalog Audi Accessories Catalog Audi Technical Articles VW-Audi Tech Forums
 
  Search our site:    
View Recent Cars  |   Cart  | Project List | Order Status | Help    
 >  >
Removing Your Audi A4 Rear Door Panels
 
Bookmark and Share

Pelican Technical Article:

Removing Your Audi A4 Rear Door Panels

Steve Vernon

Time:

1 hour1 hr

Tab:

$1000

Talent:

*

Tools:

Philips head screwdriver, trim removal tool

Applicable Models:

Audi A4 (2002-05)
Audi A4 Cabriolet (2003-06)

Parts Required:

New door panel

Hot Tip:

Get some spare door clips

Performance Gain:

Doors that work

Complementary Modification:

Replace switches

Over the life of your Audi A4, the doors will take a tremendous amount of abuse and sooner or later something will fail. If you need to service your door's mechanicals or want to freshen up the appearance with new trim you will need to remove the door panel.

The factory replacement door panels are very expensive, so if you are going to order a new panel make sure that you have the vehicle VIN number and that the interior color is correct as the panels are usually non-returnable.

Before you begin you should park the car on as level ground as possible. Nothing is more frustrating than working on the door while it is trying to swing open or closed. Also, if you are going to be working on your own car, it is a good idea to purchase a set of trim removal tools. They are a set of hard yet flexible plastic tools of different shapes and sizes that are used in removing trim pieces. They work a lot better than a flat head screwdriver and there is nothing worse than ruining a "do-it-yourself" project by scratching up your car or damaging expensive interior pieces. Pelican sells a full line of these tool sets for under $20.

There are two areas on the door panel where you will need to remove Philips head screws; the first is under the trim piece (red arrows) and the second is under the doors arm rest (yellow arrow).
Figure 1

There are two areas on the door panel where you will need to remove Philips head screws; the first is under the trim piece (red arrows) and the second is under the doors arm rest (yellow arrow).

Begin by using a trim removal tool and gently prying the trim piece from around the front of the door (red arrows).
Figure 2

Begin by using a trim removal tool and gently prying the trim piece from around the front of the door (red arrows).

Pull the five plastic snaps out (red arrows) from the front section of the trim piece.
Figure 3

Pull the five plastic snaps out (red arrows) from the front section of the trim piece. The rear section has a hook that slides into the frame (yellow arrow).

Once you have the five snaps free slide the trim piece towards the front of the door; this will allow the hook (red arrow) to slide out from the opening in the door (yellow arrow).
Figure 4

Once you have the five snaps free slide the trim piece towards the front of the door; this will allow the hook (red arrow) to slide out from the opening in the door (yellow arrow). Do not try and pull this straight out like the other fasteners as you can break the trim piece that way.

Use a Philips head screwdriver and remove the three screws (red arrows).
Figure 5

Use a Philips head screwdriver and remove the three screws (red arrows).

Continue with the Philips head screwdriver and remove the single screw under the arm rest (red arrow).
Figure 6

Continue with the Philips head screwdriver and remove the single screw under the arm rest (red arrow).

Use a trim removal tool or just your hands and starting at the lower corner separate the door panel from the door by pulling it out and away (red arrows).
Figure 7

Use a trim removal tool or just your hands and starting at the lower corner separate the door panel from the door by pulling it out and away (red arrows).

With all of the door snaps released pull and wiggle the door panel up and out of the groove it sits in on the top of the door ledge (red arrows).
Figure 8

With all of the door snaps released pull and wiggle the door panel up and out of the groove it sits in on the top of the door ledge (red arrows).

Reach between the panel and door and unclip the door release cable from the holder (red arrow) and remove the hooked end from the door handle (yellow arrow).
Figure 9

Reach between the panel and door and unclip the door release cable from the holder (red arrow) and remove the hooked end from the door handle (yellow arrow).

Disconnect the electrical connections for the power window (red arrow) and the speaker (yellow arrow) and the panel will be free from the door.
Figure 10

Disconnect the electrical connections for the power window (red arrow) and the speaker (yellow arrow) and the panel will be free from the door.

This photo illustrates the rear of the door panel.
Figure 11

This photo illustrates the rear of the door panel. You can see the four clips that help hold the panel to the door (red arrow). It is always a good idea to have extra door clips on hand when removing the panel as these do have a tendency to break. Installation is the reverse of removal.

Bookmark and Share

  Search our site:    

View Cart & CheckOut | Project List | Order Status |  Help    

 

[Home] [Customer Service] [Shopping Cart] [Project/Wish List]
  [Privacy Statement]  [Contact Us] [About Us] [Shipping] [Careers]

Copyright © Pelican Parts Inc. -    DMCA Registered Agent Contact Page

Page last updated: Fri 12/9/2016 02:46:01 AM