| BMW 2500 2800 3.0S 3.0Si Bavaria - Carburetion - Page 1 |
| Carburetors are complicated animals - mechanically metering fuel with an assortment of delicate and tiny parts. With age, seals will begin to leak and orifices may get clogged with dirt, so reconditioning is subsequently necessary. Don't risk damaging jets by running wires through them or shooting them across the room with compressed air. Replace whatever you can with original parts to ensure proper functionality for years down the road. |
|
Carburetor Gasket/Gasket Set |
| This gasket is used to seal the carburetor to the intake manifold. |
|
ZE-28K-M369 | Carburetor Kit Carburetor Kit "Major Kit" Includes the "Major Kit" Includes the Secondary Diaphragm Secondary Diaphragm (2 per Car) (2 per Car) NOTE: One kit is needed NOTE: One kit is needed per carburetor. per carburetor., 2500 2500 2800 2800 3.0 3.0 3.0S 3.0S Bavaria Bavaria
Brand: Royze [More Info] |  |
| $81.00 |  |
Vacuum Hose  |
| One of the most overlooked causes of fuel injection problems are cracked and leaking vacuum hoses. To ensure that your car will run well, you should replace these often to avoid troublesome headaches. Priced and sold by the meter. |
|
N-020-353-5-M5021 | 3.5mm ID, 7.5mm OD, (quantity as needed, priced per meter)
Brand: Contitech - Por [More Info] | |
| $4.75 | |
073379-005201-M21 | 5mm ID, 10mm OD, (quantity as needed, priced per meter)
Brand: Contitech [More Info] | |
| $6.50 | |
N-020-357-1-M21 | 7mm ID, 12mm OD, (quantity as needed, priced per meter)
Brand: Contitech [More Info] | |
| $6.75 | |
| VH-9-14 | 9mm ID, 14mm OD, (quantity as needed, priced per meter) [More Info] | No Longer Available | |
| N-020-290-1-M20 | 12mm ID, 17mm OD, (quantity as needed, priced per meter)
Brand: Cohline [More Info] | | |
10-0607-019-M21 | 14mm ID, 17mm OD, (quantity as needed, priced per meter)
Brand: Contitech [More Info] | | |
Accessories & Performance |
| Swepco 503 Fuel Improver |
| Restore lost power and clean your Fuel Injection or Carburetors. Removes impurities and particle build up. Drive your engine clean! |
|
SWE-503 | Swepco 503 Fuel Improver, 8oz [More Info] | $7.06 | |
| Air/Fuel Ratio Monitors |
The K&N Air/Fuel Monitor is designed to help the performance enthusiast calibrate and fine tune the air/fuel mixture ratio. It is an invaluable diagnostic tool that has a place in everyone's tool box, or you can install it in your car to give you real-time readings. This kit continually monitors an engine's air/fuel ratio while the engine is running. It is extremely sensitive to air/fuel ratio changes and will show them instantly and accurately, within the range of the oxygen sensor.
The instrument works whether the engine is carbureted or fuel injected, normally aspirated, turbocharged, or supercharged, and at any load condition. This precision instrument also works with nitrous oxide, but will not work with diesel or nitromethane fuels. This kit comes complete with an oxygen sensor that must be installed into the exhaust system by welding. If your 911 is already equipped with an oxygen sensor (1980-89), an air/fuel monitor may be purchased separately and wired into the existing electrical system. An oxygen sensor is also available separately.
Vehicles with dual exhaust systems (like the 911) can utilize an oxygen sensor in each headpipe or collector that is controlled by a switch that will allow each sensor or bank of cylinders to be read independently. This can show if there is a fuel distribution problem within the intake system, or help to pinpoint a potential problem in advance. |
|
PEL-SW85-2437 | Rectangle Surface mount Air/Fuel Ratio Monitor Kit, w/oxygen sensor [More Info] | $199.55 | |
PEL-SW85-2441 | Round In Dash mount Air/Fuel Ratio Monitor Kit, w/oxygen sensor [More Info] | $206.30 | |
PEL-SW85-2439 | Rectangle Surface mount Air/Fuel Ratio Monitor Kit, without oxygen sensor [More Info] | $137.27 | |
PEL-SW85-2442 | Round In Dash mount Air/Fuel Ratio Monitor Kit, without oxygen sensor [More Info] | No Longer Available | |
PEL-SW85-2438 | Replacement Oxygen Sensor [More Info] | $82.00 | |
PEL-SW85-2440 | O2 Sensor Plug and Fitting [More Info] | $23.60 | |
| PEL-SW85-21688 | Weld on Fitting [More Info] | $10.50 | |
PEL-SW85-21686 | O2 Sensor Plug [More Info] | $16.15 | |
