Order Online or Call:  
888-280-7799  
HACKER SAFE certified sites prevent over 99.9% of hacker crime.
  Search our site:   

View Cart  | Project List | Order Status |  Help    

 
- Back to Catalog -
Lug Nut Soft Socket
12-Point/12mm Flywheel Socket
Flywheel Lock
Oil Filter Wrenches
Hub/Bearing Extractor and Installer Kit
Dial Gauge
Valve Spring Tools
Pulley Wrench Tools
Mechanical Injection pump tools
CIS Fuel Enrichment Wrench
Bosch CIS Tester
Ball Joint Tools
Tie Rod Tools
Factory Timing Belt Tensioning Tool
Synchrometer
Allen Head Tools
CV Bolt Removal Tool
Magnetic Box "V" Wrench (17mm)
Suspension Alignment Tools
Ride Height Wrench
Extraction Tools
Spanner Wrench Set
32 MM Oil Line Wrench
36 MM Oil Line Wrench
Clutch Alignment Tool
Custom Service Cover
Fuel Injection Diagnostic Tools
OBD-II ScanTool
Digital Air/Fuel Ratio Meter
Jack Stands
Stud Removal Tools
Dremel 83pc Variable Speed Moto-Tool Kit
- Back to Catalog -
Home >  928 (1978-95)Tools & Books >   Porsche 928 Tools  
Porsche 928 Tools - Page 3

Factory Timing Belt Tensioning Tool

The tool below are all that's needed to take the guess work out of properly adjusting your timing and balance shaft. The belts must be adjusted every 15,000 miles and doing so is the only way to ensure long engine life. If you are going to keep the car, you might as well day, or you will want to see the car after a services. The Tensioning tool is Made in Germany, same tool the factory technicians use. Comes with a factory 2 year Limited Warranty.944 Balance Shaft Locking Bar - The balance shaft locking bar is used during the timing belt replacement process on 944s. It is designed to keep the balance shaft sprocket from turning while removing/replacing the retaining bolt.Timing Belt Adjusting Tool-This specially designed tool makes adjusting the timing belt a snap. Balance Shaft Belt Gauge - This tool has also proved invaluable to properly adjust the roller for the balance shaft toothed belt.

000-721-920-10-OEM

Factory Timing Belt Tensioning Tool, 944 (3/1983-89), 924S/944S (1987-88), 944S2 (1989-91), 944 Turbo (1986-89), 968 (1992-95)
   Brand: Genuine Porsche    [Photo]

$597.75

PEL-TOL-P232

Aftermarket 944 Balance Shaft Locking Bar    [Photo]

$49.00

000-721-920-00-OEM

Factory 944 Balance Shaft Locking Bar
   Brand: Genuine Porsche    [Photo]

$129.50

000-721-920-12-OEM

Calibration Bar
   Brand: Genuine Porsche    [Photo]

$34.50

000-721-920-70-OEM

Balance Shaft Belt Gauge
   Brand: Genuine Porsche    [Photo]

$28.50

Synchrometer

Synchronizing your Porsche mechanical fuel injection or carburetors with our tool, is the only way to precisely measure the air intake for optimum power and a smooth idle.

PEL-TOL-STESK

Mechanical Injection/carburetor Synchrometer    [Photo]

$53.80

Allen Head Tools

Removing your 911 heads or heat exchangers can be very difficult without the correct tools for the job. With these extra long Allen extensions, those nuts cannot hide. The 10mm tool is used for removing and tightening the head studs on the 911 motor. The 8mm tool is used to remove and tighten the 911 heat exchanger nuts.

PEL-TOL-A10MM

Allen Head Nut Removal Tool for 911 Head Studs (10mm)    [Photo]

$29.95

PEL-TOL-P243

Allen Heat Exchanger Nut Removal Tool (8mm)    [Photo] [Photo]

$31.00

CV Bolt Removal Tool

Avoid stripping your bolt heads and spending wasted hours cutting and grinding them off by using this special tool to easily remove those pesky CV joint bolts. This tool is for use with 12-point star-shaped bolts only. Please make sure to check your bolts before ordering. It's common for previous owners to replace the 12-point star shaped bolts with more standard allen head bolts instead. Although the 12-point pattern allows you to get a better grip on the bolts (with the correct tool), and apply the high torque that the bolts require, previous owners may have stripped out these bolt heads by attempting to use a torx or hex driver instead of the proper tool. A word of caution here - these other tools MAY work, but if they strip the bolt head, then you are in for an entire afternoon of grinding it off the next time it's replaced.

TIP: Spray the bolts down with WD-40 or Liquid Wrench first to loosen the dirt and debris in the bolt head, then scrape out any dirt that may be left. With the socket on a 6" extension, slip the tool into the bolt head and give it a gentle rap on the end with a mallet to seat it firmly. Following this simple procedure will hopefully avoid you from stripping any CV bolts.

PEL-CV-T1

CV Joint Bolt Removal Tool - 8mm, 12-point Socket Driver, 3/8 in. drive    [Photo]

$29.95

Magnetic Box "V" Wrench (17mm)

This unique-looking tool is used to aid in the removal of the engine/transmission bolts. The V-Wrench holds the nut on the other side of the engine compartment so that you can remove the nut from the transmission. The V design holds the nut steady, unlike a normal wrench, and allows you to remove the bolt on the other side without the help of an assistant.

PEL-TOL-P222

Magnetic Box "V" Wrench (17mm)     [Photo]

$33.00

Suspension Alignment Tools

Doing some adjustments to your suspension? Using the right tools can help you obtain exactly the values that you are looking for.

PEL-TOL-P221

Rear Suspension Toe-In Adjuster, 911 All     [Photo]

$28.00

PEL-TOL-P235

Camber Adjuster, 911, C2 and C4     [Photo]

$21.00

Ride Height Wrench

don't be without this Ride Height Combination Wrench went setting up your suspension! Fits the spring plate eccentric 24mm and 36mm bolts. Powder coated for a long lasting finish.

PWE-2436RHW

Ride Height Combination Wrench, 911 1977-89     [Photo]

$30.70

  Page 3 of 5  <12345>

        

  Search our site:   

View Cart & CheckOut | Project List | Order Status |  Help    

 

[Home] [Customer Service] [Shopping Cart] [Project/Wish List]
  [Privacy Statement]  [Contact Us] [About Us] [Shipping]

Copyright © 2008, Pelican Parts Inc.