| Porsche 928 Tools - Page 2 |
Hub/Bearing Extractor and Installer Kit  |
| Want to save on a costly repair, replace your own bearing or pull your own hubs with our all in one Porsche kit. Designed to efficiently remove and install hub and wheel bearings, this kit will make the notoriously difficult job of removing rear wheel bearings a breeze. The kit comes with a set of adapters specific to the Porsche series, but can also be used on all front and rear wheel drive vehicles with independent suspension. Also for R&R of the rear wheel bearings only on models with drum brakes independent rear suspension. |
|
| PEL-TOL-SIRB90-P3 | Hub/Bearing Extractor and Installer Kit, 928 All [More Info] | $275.00 |  |
PEL-TOL-P231 | Oil Seal Installation Tool for 944, Balance Shaft [More Info] | $38.60 | |
PEL-TOL-P218 | Oil Seal Alignment Tool for 944 (1983-86) [More Info] | $20.70 | |
Dial Gauge |
| A must for every Porsche owner, this metric dial gauge is not only useful, but it's also cool looking too! 0-10MM travel. Measures in 100ths of a millimeter. All steel and brass construction. Resettable pointers. Use with any standard holder. The Metric Dial Gauge is a requirement for setting the sensitive timing adjustment of the cams when rebuilding a 911 motor. It's also essential when measuring the flywheel and crank shaft end play. The Z-block fixture is designed to hold the dial gauge while adjusting the 911 camshaft timing, and also comes with a dial gauge extension pin. The Dial Gauge Holder is designed to hold the gauge while measuring flywheel and pulley end play. |
|
TOL-721-T63 | Metric Dial Gauge [More Info] | $79.00 | |
PEL-TOL-SDG1 | Standard Dial Gauge [More Info] | Temporarily unavailable | |
PEL-TOL-P207 | Dial Gauge Holder (Z Block), w/extension Pin [More Info] | $36.10 | |
PEL-TOL-P240 | Dial Gauge Holder [More Info] | $35.20 | |
Valve Spring Tools |
| Replacing your valve springs? Make quick work of this job with our specialized tool, designed specifically for the 911. The tool mounts to one of the studs on the heads and compresses the spring so that the valve keepers may be removed. Tools are specifically designed for either intake or exhaust valves. |
|
PEL-TOL-P7E | Valve Spring Compressor, Exhaust, 911 (1965-89) [More Info] | $59.60 | |
PEL-TOL-P71 | Valve Spring Compressor, Intake, 911 (1965-89) [More Info] | $59.60 | |
Pulley Wrench Tools |
| Need to tighten that loose fan Belt? don't use a screwdriver to hold the pulley - get the correct tool for the job! Keep in mind that correct fan belt attachment is essential to keep your engine running cool. It is nearly impossible to obtain the correct tension on the fan belt pulley without this tool. Before you purchase one from us though, make sure that you check the factory tool kit that came with the car - there should be one in there. Important Tip: The pulley and fan belt must use six shims at all times, either on the inside or the outside. Make sure that you place the extra shims on the outside. If you don't, then the nut will bottom out and the fan belt will not tighten properly, no matter how hard you try. |
|
PEL-TOL-P209 | Alternator Pulley Wrench, 911 (1975-89) [More Info] | $32.70 | |
PEL-TOL-P208 | 911 Fan Pulley Wrench, 911 (1965-74)
Brand: SIR Tools [More Info] | $27.70 | |
PEL-PW-FPW | 911 Fan Pulley Wrench, 911 (1965-74)
Brand: Wilding Engineering [More Info] | $28.00 | |
Mechanical Injection pump tools |
| The Adjustment Driver Kit contains three tools specifically designed to help you adjust the mechanical injection pump for performance or emissions tuning. One tool is used to remove a plug on the pump accessed through the fan. The other two are used for actually adjusting the pump's settings. |
|
PEL-TOL-P206 | Mechanical Injection Pump Adjustment Driver Kit, 911 (1969-73) [More Info] | $43.60 | |
| CIS Fuel Enrichment Wrench |
| Adjusting your CIS injection will nearly be impossible without this handy tool. Made from hardened steel for many years of service. NOTE: This is a generic wrench and may need to be cut down to fit your particular application. |
|
UN-120-1334 | CIS Fuel Enrichment Wrench [More Info] | $5.85 | |
