| Porsche 928 Tools - Page 1 |
| If you are opting to save money by working on your car yourself, it is a very wise investment to have the proper tools. Some tasks may be nearly impossible to perform without the specific tool designed to assist you in the process. Do it right with the right tools. Some tools may be special order, and may take a few days to be shipped out. All tools sold by Pelican Parts are not returnable, except for warranty repair or replacement. |
|
Lug Nut Soft Socket |
Every Porsche owner needs a Soft Socket in their tool box! This high quality, chrome plated lug nut socket was designed with inlaid high impact nylon to prevent rounded corners or scratches on your lug nuts. Cannot be used with air tools.
NOTE: Not for use with steel lug bolts/nuts, ONLY for original aluminum lug nuts! Also not to be used to break stuck lug nuts free from the wheels! |
|
PEL-SS-19 | Lug Nut Soft Socket [Photo] | $25.45 |  |
| This special thin walled, heavy duty IMPACT socket with a riveted Aluminum insert was developed for the crucial task of R&R of wheel lugs nuts/bolts without marring or scuffing the surface of the wheel or bolts. Measuring at 3.5" to fit into deep recess of wide wheels. Comes with a limited life-time warranty, guaranteed to be the last 19mm wheel lug socket you'll ever buy. |
|
PEL-TOL-LUG19MM | Impact Duty Soft-Walled Lug Nut Socket - 19mm [Photo] | $28.30 | |
12-Point/12mm Flywheel Socket |
| Get the correct socket to remove/install those Flywheel Bolts ! |
|
TOL-SK41422 | Flywheel Bolt Socket Tool, 12-Point/12mm [Photo] [Photo] | $19.95 | |
Flywheel Lock |
| Getting ready to remove that flywheel? You're going to need this original factory flywheel lock. Makes that job so much safer and easier! |
|
| 000-721-916-10-OEM | Flywheel Lock Tool (1978-82), 928 | $55.50 | |
| 000-721-916-11-OEM | Flywheel Tool Late, (1983-95), 928 | $55.50 | |
Oil Filter Wrenches |
| Get off easily with our new oil filter wrench! This wrench attaches directly to the top of the oil filter and allows you to attach a standard 3/8" drive ratchet to remove the filter. Gone are the days of poking messy holes in the filter just to get a screwdriver in there to remove it from the oil tank. |
|
PEL-PP903124 | Oil Filter Removal Socket Wrench Tool - 911/C2/C4 (1965-94), 911 Turbo (1976-89) [Photo] | $10.10 | |
Hub/Bearing Extractor and Installer Kit  |
| Want to save on a costly repair, replace your own bearing or pull your own hubs with our all in one Porsche kit. Designed to efficiently remove and install hub and wheel bearings, this kit will make the notoriously difficult job of removing rear wheel bearings a breeze. The kit comes with a set of adapters specific to the Porsche series, but can also be used on all front and rear wheel drive vehicles with independent suspension. Also for R&R of the rear wheel bearings only on models with drum brakes independent rear suspension. |
|
| PEL-TOL-SIRB90-P3 | Hub/Bearing Extractor and Installer Kit, 928 All | $166.00 | |
PEL-TOL-P231 | Oil Seal Installation Tool for 944, Balance Shaft [Photo] | $40.00 | |
PEL-TOL-P218 | Oil Seal Alignment Tool for 944 (1983-86) [Photo] | $20.00 | |
Dial Gauge |
| A must for every Porsche owner, this metric dial gauge is not only useful, but it's also cool looking too! 0-10MM travel. Measures in 100ths of a millimeter. All steel and brass construction. Resettable pointers. Use with any standard holder. The Metric Dial Gauge is a requirement for setting the sensitive timing adjustment of the cams when rebuilding a 911 motor. It's also essential when measuring the flywheel and crank shaft end play. The Z-block fixture is designed to hold the dial gauge while adjusting the 911 camshaft timing, and also comes with a dial gauge extension pin. The Dial Gauge Holder is designed to hold the gauge while measuring flywheel and pulley end play. |
|
PEL-TOL-MDG1 | Metric Dial Gauge, German-made [Photo] | $49.95 | |
PEL-TOL-SDG1 | Standard Dial Gauge [Photo] [Photo] | Temporarily unavailable | |
PEL-TOL-P207 | Dial Gauge Holder (Z Block), w/extension Pin [Photo] | $38.00 | |
PEL-TOL-P240 | Dial Gauge Holder [Photo] | $37.00 | |
