| Porsche 914 Tools - Page 7 |
36 MM Oil Line Wrench |
| Having trouble removing the large oil lines on your Porsche? Then this is the wrench for you. Precision laser cut 36MM wrench with sculpted handle for maximum grip on the fitting and in your hand. 12 point design will not slip off or round fittings like open-end wrenches do. 15 degree head design allows wrench to operate in the tight confines of the engine compartment. If you own a Porsche 911, 930, 914-6, you'll need this wrench. |
|
PEL-PW-OLW | 36 MM Oil Line Wrench [More Info] | $31.95 |  |
Clutch Alignment Tool  |
| The clutch alignment tool is used to orient the clutch disc with respect to the flywheel when mounting your pressure plate. You may have tremendous difficulty remating the transmission and the engine if the disc is misaligned with the pressure plate upon assembly. |
|
PEL-TOL-CA1 | Clutch Alignment Tool (Spline count = 24; Pilot diameter = 14.7 mm; Spline diameter = 20.6 mm), 356 All, 911 (1965-71), 912/912E, 914 All, 924 (1976-82) [More Info] | $8.85 | |
PEL-TOL-CA2 | Clutch Alignment Tool (Spline count = 20; Pilot diameter = 14.9 mm; Spline diameter = 22.2 mm), 911 (1972-86) [More Info] | $8.85 | |
PEL-TOL-CA3 | Clutch Alignment Tool (Spline count = 23; Pilot diameter = 14.9 mm; Spline diameter = 25.4 mm), 911, C2/4, 993 (1987-98), 911/C2/993 Turbo, 944/944 Turbo/968 [More Info] | $8.85 | |
Air/Fuel Ratio Meter |
| WEGO IV Wide-Band Air/Fuel Ratio Tuning Aid |
The WEGO IV is a highly accurate and complete air/fuel ratio metering system with built-in data logging. The unit displays air/fuel ratio (AFR) and continuously logs over 2 hours of data, including AFR, engine RPM, and a spare 0-5V analog input for sensors such as throttle position or manifold pressure.- Includes Bosch LSU 4.2 oxygen sensor, 96" sensor extension cable, 18 x 1.5 mm weld nut for exhaust pipe, USB cable, and software for downloading and charting
- Data is easily exported to a spreadsheet
- Attractive black anodized aluminum housing with convenient front panel mini USB port, compact size: 3.3"L x 2.1"W x 0.9"H
- RPM input signal connects directly to Porsche tachometer - no adapter required
- Easy free-air calibration for sensor aging effects
- Ultra-bright daylight readable blue LED display and automatic dimming under low light conditions
- 0-5V analog AFR output for interface to dyno instrumentation
- Industrial grade clamping terminal block on rear panel allows easy hookup
Available in either single or dual channel. Dual channel unit displays and logs two channels of AFR data. The 12 foot extension cable is sold separately and is necessary for installation in a rear engine car (two are required for the dual-channel unit). |
|
IG3-114001 | WEGO IV Wide-band AFR Gauge and Data Logger [More Info] | $460.00 | |
IG3-113001 | WEGO IV Dual Channel Wide-band AFR Gauge and Data Logger [More Info] | $687.50 | |
IG3-115004 | WEGO 12 Foot Extension Cable [More Info] | $29.50 | |
| Innovate Motorsports LM-2 |
The LM-2 combines an air/fuel ratio meter, a full-function 32-channel datalogger, and powerful software to deliver a complete tuning workshop for less than the cost of one dyno day. Whether you have a piggy-back fuel controller, race carb, aftermarket ECU, ODB-II tuning software, or a flash/chip programmer, an LM-2 is the tool you need to dial in maximum HP. The meters digital signal processing technology provides data on exactly how rich or lean an engine is running at any load. The LM-2s self-calibrating circuitry also compensates for changes in temperature, altitude, and sensor condition. - Patented Direct Digital Wideband Technology
- Wideband O2 Compatible with ALL fuel types
- Single or Dual Channel Version Available
- OBD-II Scan tool- read/clear DTCs and log up to 16 channels of CAN OBD-II Data
- Log directly to SD card (included)
- Playback log data on screen and/or with powerful LogWorks software (included)
- Large high-contrast graphics LCD
- Built-in RPM converter (direct frequency or with optional inductive clamp)
- 4 fully-differential analog inputs
- 2 configurable linear analog outputs
- Positive lock connectors for all connections
- Innovate MTS serial IN and OUT
- USB connection to your PC
The LM-2 also features two fully programmable linear analog outputs to connect to analog gauges, dyno computers, ECUs, piggyback controllers, and other devices with analog inputs. Analog output 1 comes setup from the factory ready for narrowband simulation; analog output 2 is configured as 0 volt = 7.35 AFR and 5 volts = 22.39 AFR. With the provided LM Programmer software these analog outputs may also be configured by the user.
The LM-2 Kit (Single Wideband O2) includes the LM-2 meter, Bosch wide-band oxygen sensor, 10 ft sensor cable, cigarette-lighter power adapter, analog in/out cable, ODB-II/CAN interface cable, SD memory card, USB cable for PC connection, weld-in bung and plug, LogWorks software CD, and quick-start guide. Carrying Case also included!
More accessories for your LM-1 available here.
For permanently installed tuning solutions, click here.
Manufacturer: Innovate Motorsports
Click here to visit the manufacturer's home page. |
|
INN-3806 | Innovate Motorsports LM-2: Digital Air/Fuel Ratio Meter [More Info] | $479.00 | |
Stud Removal Tools |
| This tool incorporates a collet that latches onto and compresses the threads of the stud, squeezing them tight. Then the tool and the stud can be removed. If you are removing studs from an engine case, an extra vise-grip or two might be useful as well to get more torque on the studs. |
|
PEL-SNAPON-CG500-2 | Stud Remover Collet Tool [More Info] | $93.75 | |
PEL-SNAPON-CG500-43 | Stud Remover Collet, M10x1.5 [More Info] | $55.00 | |
PEL-SNAPON-CG500-37 | Stud Remover Collet, M8x1.25 [More Info] | $55.00 | |
Dremel Variable Speed Rotary Tool Kit |
This variable speed (5,000 - 35,000 rpm) tool comes with 24 accessories for polishing, cutting, sanding, grinding and more. Combining the correct speeds and bits, you can complete all kinds of tasks on a multitude of materials. Includes a molded case.
Manufacturer: DREMEL
Click here to visit the manufacturer's home page |
|
TOL-DRE300-124 | Dremel Variable Speed Rotary Tool Kit [More Info] | No Longer Available | |
