|  | | | Porsche 914 Tools - Page 5 | 36 MM Oil Line Wrench | | Having trouble removing the large oil lines on your Porsche? Then this is the wrench for you. Precision laser cut 36MM wrench with sculpted handle for maximum grip on the fitting and in your hand. 12 point design will not slip off or round fittings like open-end wrenches do. 15 degree head design allows wrench to operate in the tight confines of the engine compartment. If you own a Porsche 911, 930, 914-6, you'll need this wrench. |
| 
PEL-PW-OLW | 36 MM Oil Line Wrench [More Info] | $31.95 |  | Clutch Alignment Tool  | | The clutch alignment tool is used to orient the clutch disc with respect to the flywheel when mounting your pressure plate. You may have tremendous difficulty remating the transmission and the engine if the disc is misaligned with the pressure plate upon assembly. |
| 
PEL-TOL-CA1 | Clutch Alignment Tool (Spline count = 24; Pilot diameter = 14.7 mm; Spline diameter = 20.6 mm), 356 All, 911 (1965-71), 912/912E, 914 All, 924 (1976-82) [More Info] | $8.85 | | 
PEL-TOL-CA2 | Clutch Alignment Tool (Spline count = 20; Pilot diameter = 14.9 mm; Spline diameter = 22.2 mm), 911 (1972-86) [More Info] | $8.85 | | 
PEL-TOL-CA3 | Clutch Alignment Tool (Spline count = 23; Pilot diameter = 14.9 mm; Spline diameter = 25.4 mm), 911, C2/4, 993 (1987-98), 911/C2/993 Turbo, 944/944 Turbo/968 [More Info] | $8.85 | | Digital Air/Fuel Ratio Meter | The LM-2 combines an air/fuel ratio meter, a full-function 32-channel datalogger, and powerful software to deliver a complete tuning workshop for less than the cost of one dyno day. Whether you have a piggy-back fuel controller, race carb, aftermarket ECU, ODB-II tuning software, or a flash/chip programmer, an LM-2 is the tool you need to dial in maximum HP. The meters digital signal processing technology provides data on exactly how rich or lean an engine is running at any load. The LM-2s self-calibrating circuitry also compensates for changes in temperature, altitude, and sensor condition. - Patented Direct Digital Wideband Technology
- Wideband O2 Compatible with ALL fuel types
- Single or Dual Channel Version Available
- OBD-II Scan tool- read/clear DTCs and log up to 16 channels of CAN OBD-II Data
- Log directly to SD card (included)
- Playback log data on screen and/or with powerful LogWorks software (included)
- Large high-contrast graphics LCD
- Built-in RPM converter (direct frequency or with optional inductive clamp)
- 4 fully-differential analog inputs
- 2 configurable linear analog outputs
- Positive lock connectors for all connections
- Innovate MTS serial IN and OUT
- USB connection to your PC
The LM-2 also features two fully programmable linear analog outputs to connect to analog gauges, dyno computers, ECUs, piggyback controllers, and other devices with analog inputs. Analog output 1 comes setup from the factory ready for narrowband simulation; analog output 2 is configured as 0 volt = 7.35 AFR and 5 volts = 22.39 AFR. With the provided LM Programmer software these analog outputs may also be configured by the user.
The LM-2 Kit (Single Wideband O2) includes the LM-2 meter, Bosch wide-band oxygen sensor, 10 ft sensor cable, cigarette-lighter power adapter, analog in/out cable, ODB-II/CAN interface cable, SD memory card, USB cable for PC connection, weld-in bung and plug, LogWorks software CD, and quick-start guide. Carrying Case also included!
More accessories for your LM-1 available here.
For permanently installed tuning solutions, click here.
Manufacturer: Innovate Motorsports
Click here to visit the manufacturer's home page. |
| 
INN-3806 | Innovate Motorsports LM-2: Digital Air/Fuel Ratio Meter [More Info] | $479.00 | | Stud Removal Tools | | This tool incorporates a collet that latches onto and compresses the threads of the stud, squeezing them tight. Then the tool and the stud can be removed. If you are removing studs from an engine case, an extra vise-grip or two might be useful as well to get more torque on the studs. |
| | PEL-SNAPON-CG500-2 | Stud Remover Collet Tool [More Info] | $93.75 | | | PEL-SNAPON-CG500-43 | Stud Remover Collet, M10x1.5 [More Info] | $45.45 | | | PEL-SNAPON-CG500-37 | Stud Remover Collet, M8x1.25 [More Info] | $45.45 | | Dremel 83pc Variable Speed Moto-Tool Kit | Cut, grind, carve, rout, sharpen, drill, polish, or sand. If you can dream it, you can do it with the MultiPro kit. Combining the correct speeds and bits, you can complete all kinds of tasks on a multitude of materials.
Variable speed, from 5,000 to 35,000 rpm
Quick-change collet
Flexible shaft attachment, 75 bits, and two clamps
2-year warranty
The kit includes the MultiPro tool, convenient case with storage compartments, wrench, 75 bits, flex shaft, two clamps, the Dremel chuck, garden tool sharpening attachment, and a book of 175-plus uses for the MultiPro kit.
Manufacturer: DREMEL
Click here to visit the manufacturer's home page |
| 
TOL-DRE3956-02 | 83pc Variable Speed Moto-Tool Kit [More Info] | $135.75 | |
| |
|
|
|
