| Porsche 911 & Carrera Axles & Bearings - Page 2 |
CV Joints & Gaskets |
| CV Joint Gaskets |
901-332-297-00-M260 | CV Joint Gasket, each, 911 (1969-early 75)
Brand: OEM [More Info] |  |
| $2.50 |  |
| 923-332-297-00-M30 | CV Joint Gasket, each, 911 (late 1975-84)
Brand: Elring Klinger [More Info] | |
| $2.50 | |
| 930-332-297-00-M260 | CV Joint Gasket, each, 911 Turbo (1976-86)
Brand: OEM [More Info] | |
| $2.25 | |
| CV Joint Hardware |
900-067-229-09-M260 | 911 CV Joint Bolt, 10x48mm (1974-early '75 manual transmission cars with VIN up to 9115201529 Coupe, 9115210859 Targa, 9115400173 Carrera Coupe, 9115410088 Carrera Targa)
Brand: OEM [More Info] | |
| $1.25 | |
900-067-211-09-M260 | 911 CV Joint Bolt, 8x50mm (late 1975-early 85)
Brand: OEM [More Info] | |
| $1.50 | |
900-067-123-01-M153 | 911 CV Joint Bolt, 10x50mm (late 1985-89), 911 Turbo (1985-94)
Brand: Kamax [More Info] | |
| $1.25 | |
900-067-118-01-M100 | 911 Turbo CV Joint Bolt, 10x60mm (1978-86)
Brand: Genuine Porsche [More Info] | |
| $4.00 | |
911-332-191-00-M100 | CV Joint Backing Plate, 3 per joint, 911 (models that use 10mm bolt)
Brand: Genuine Porsche [More Info] | |
| $10.75 | |
999-523-103-01-OEM | CV Joint Lock Washer, 911 (1975-early 75)
Brand: Genuine Porsche [More Info] | $0.75 | |
999-041-012-01-OEM | CV Joint Snap Ring, 911 (1974-75)
Brand: Genuine Porsche [More Info] | $2.75 | |
999-041-016-01-OEM | CV Joint Snap Ring, 911 (1975-84)
Brand: Genuine Porsche [More Info] | $1.50 | |
999-152-084-01-OEM | CV Joint Snap Ring, 911 (1985-89), 911 Turbo (1976-89)
Brand: Genuine Porsche [More Info] | $1.00 | |
999-095-019-00-OEM | CV Joint Roll Pin (sold per each, 2 per joint), 911 (1974-83)
Brand: Genuine Porsche [More Info] | $2.75 | |
Axles / Half-shafts |
Replace your bent or damaged axle with a brand new one! includes new CV joints and boots on both ends. Save yourself a tremendous amount of labor by purchasing a complete bolt-in axle. Spend more time working on all of those other problems!
In 1985 Porsche changed the outer diameter of the 911 Carrera CV joint from 100mm to 108mm (same as 911 Turbo). This change started in the 1985 USA model year. There are some early model 1985 cars with earlier version C/V joints. Please make sure that you measure your CV joint diameter before ordering to make sure that you obtain the right one for your car.
Manufacturer: Lobro - Porsche OEM Supplier |
|
911-332-033-09-M60 | Complete Axle w/two CV Joints & Boots (bolts not included), 2 per car sold per each, 911 (1974- mid 75)
Brand: GKN Loebro [More Info] | |
| $241.25 | |
923-332-033-02-M60 | Complete Axle w/two CV Joints & Boots 911, 100mm (Jan 1975-early 85), Requires 47mm bolts (included)
Brand: GKN Loebro [More Info] | |
| $267.75 | |
911-332-024-15-M60 | Complete Axle w/two CV Joints, Boots, and Bolts 911, 108mm (late-1985-89)
Brand: GKN Loebro [More Info] | |
| $326.25 | |
930-332-037-00-M100 | Complete Axle w/two CV Joints & Boots 911 Turbo (1976-84)
Brand: Genuine Porsche [More Info] | |
| $460.00 | |
930-332-037-04-M60 | Complete Axle w/two CV Joints & Boots 911 Turbo (1985-89)
Brand: GKN Loebro [More Info] | |
| $263.25 | |
Wheel Bearings & Hub Parts  |
Wheel bearings are one of the parts that routinely wear out on older cars. With the car off the ground, check the wheel for any wobbling or excessive noise. Replace bearings in pairs. Tech Tip: Freeze the rear bearings prior to installation. The cold temperatures will make them shrink slightly and be easier to press in. They also make a nice snack when served with ice cream.
Manufacturer: SKF or FAG - Porsche OEM Suppliers |
|
