| Porsche 911 & Carrera Miscellaneous - Page 21 |
Replica Fuchs Alloy Wheels |
| Euromeisterญฎ presents these Alloy Replica 5-spoke style wheels. Manufactured using water & air cooled low pressure casting equipment resulting in the strongest and lightest cast aluminum wheels on the market. This design allows them to manufacture a wheel only slightly heavier than a more expensive forged wheel. Finished wheels are then completely X-Rayed to insure quality and strength. Wheels come with black centers and a machined lip. All wheels are hub-centric with the standard 5x130mm lug pattern. Euromeisterฎ Wheels utilize original factory offsets to fit 1965-89 911,912,930 with Carreraฎ or Turbo flares, 944 1983-86 except Turbo and 914-6 with GT Flares. Wheels accept the original 70mm ring clip cap standard on most Porscheฎ vehicles. Center caps and lug nuts sold separate. |
|
PEL-915737 | Euromeister Alloy Replica Wheel this item has been discontinued and we have only one wheel in stock, 16x7 (23.3 offset), Each [More Info] | $199.95 |  |
PEL-915738 | Euromeister Alloy Replica Wheel, 16x8 (10.6 offset), Each [More Info] | Temporarily unavailable | |
PEL-915739 | Euromeister Alloy Replica Wheel this item has been discontinued and we have only one wheel in stock, 16x9 (15.0 offset), Each [More Info] | $249.95 | |
Oil Cooler Air Scoop |
| Does your Porsche operate at a higher oil temp than you would like ? With our custom made oil cooler scoop, this will no longer be a problem. Direct cooling air right onto the oil cooler. Manufactured out of fiberglass, the grain and texture of this scoop is designed to match the look of the rubber bumper pieces. Blends in so well, you would hardly know that its there, except for the cooler temperatures! |
|
PEL-JM-DUCT | Oil Cooler Air Scoop [More Info] | $89.95 | |
Cup Holder |
| This clever cup holder holds your favorite standard-size beverage (the opening is about 3-1/8" in diameter) without requiring ANY alterations or modifications to your interior. You simply slide it onto your seat rail and tighten the thumbscrew. The thumbscrew even has a rubber bumper at the tip to protect the rail! |
|
PEL-EVOSC91144 | Evo SuperCup Cup Holder, 911 (1965-98), 930, and 944 [More Info] | $49.99 | |
Finally, the cup-holder Porsche owners have always needed. Cups, cans and water bottles at your fingertips. Far enough over to avoid interference when shifting, yet at your fingertips when needed. The ingenuous design locks into your cigarette lighter port with an expanding plug and stays there until you remove it with a quick turn of the thumbscrew. All steel construction with an insulated end and black powder-coated for a tough, long-lasting finish. Are you tired of cup-holders that wont stick where you put them; drinks leaking into your door pockets because you forgot they were there when you closed the door? Tested with over 2 lbs. of ballast for over 2 months to ensure a strong and secure holder.
A cup-holder mounted closest to the center of the car is less likely to spill and the most convenient location for the driver. |
|
PEL-JM-CUP | Cup Holder, Aftermarket, 911 (1974-89), Each [More Info] | $37.75 | |
Finally, the cup-holder Porsche owners have always needed. Cups, cans and water bottles at your fingertips. Far enough over to avoid interference when shifting, yet at your fingertips when needed. The ingenuous design locks into your cigarette lighter port with an expanding plug and stays there until you remove it with a quick turn of the thumbscrew. All steel construction with an insulated end and black powder-coated for a tough, long-lasting finish. Are you tired of cup-holders that wont stick where you put them; drinks leaking into your door pockets because you forgot they were there when you closed the door? Tested with over 2 lbs. of ballast for over 2 months to ensure a strong and secure holder.
A cup-holder mounted closest to the center of the car is less likely to spill and the most convenient location for the driver. |
|
Bumper Shocks |
| Playing a little bumper tag? Your 'impact' bumpers may have been enough to absorb any cosmetic damage, but the (one-time use) shocks that operate beneath them are now spent. Replace them with new ones to restore the proper functionality of your bumpers and protect the safety of your passengers. |
|
| 911-505-279-03-OEM | Front Hydraulic Bumper Shock (sold per each, 2 required), 912E (1976), 911 (1974-89)
Brand: Genuine Porsche [More Info] | $556.25 | |
| 911-505-280-03-M10 | Rear Hydraulic Bumper Shock (sold per each, 2 required), 912E (1976), 911 (1974-89)
Brand: Sachs [More Info] |  |
| $43.25 | |
| 911-505-221-00-M100 | Bumper Shock Bushing (Rubber Isolator), Front and Rear (4 per car, sold individually), 911 (1974-89), 912E, 911 Turbo (1976-89)
Brand: Genuine Porsche [More Info] | |
| $24.25 | |
| 911-505-311-00-M100 | Bumper Shock Base, Front and Rear (4 per car, sold individually), 911 (1974-89), 912E, 911 Turbo (1976-89)
Brand: Genuine Porsche [More Info] | |
| $7.75 | |
Fire Extinguisher |
| Double the size and fire-fighting-power of the smaller units. Attractive billet aluminum nozzle. Extinguishing agent: Halotron 1 (2.5 lb)
Extinguisher weight: 5.4 lb
14.8 in x 3.0 in
Width: 5.0 in
UL rating: 2B:C
Rechargeable
Steel canister
All metal valve construction
EPA approved
One year limited warranty |
|
PEL-HG250R | H3R HalGuard Halotron 1 Fire Extinguisher, 2.5 lb. (Red) [More Info] | $119.95 | |
Fire Extinguisher Mount |
| PCA driving events require cars to be equipped with a 2.5 lb. extinguisher within easy reach of the driver - requirements aside, it's a good idea to have a fire extinguisher in any valuable car. These Brey-Krause mounts conveniently locate the extinguisher in front of the driver or passenger seat. It moves with the fore/aft seat adjustment and thereby remains out of the way (Quick Release Clamp for fire extinguisher is sold separately). |
|
BK-R-2015 | Brey-Krause Fire Extinguisher Mount - (Non-Powered Seat) 911 (1974-98) [More Info] | $89.00 | |
BK-R-2016 | Brey-Krause Fire Extinguisher Mount - (Powered Seat) 911 (1974-98) [More Info] | $89.00 | |
BK-R-2010 | Brey-Krause Adapter Bracket for Fire Extinguisher Mount R-2016 (Allows 2 1/2in Additional Forward Seat Movement) [More Info] | $20.00 | |
