| Porsche 911 & Carrera Pistons, Cylinders, and Heads - Page 6 |
Cylinder Head Studs and Hardware |
| Non-Corrosive Exhaust Stud Hardware |
Phew... you finally got them off. So why put the same carbon steel ones back in? Replace your corroded factory exhaust studs with aircraft-grade ones that will last a lifetime. These non-corrosive studs are manufactured from an advanced alloy which has a high tensile strength and no brittle characteristics. All stud threads are rolled (not cut) to offer maximum fatigue characteristics while maintaining exacting tolerances.
The austenitic alloy locknuts are prepped and electroplated to create a high temperature oxidation barrier as well as an anti-galling surface at the thread interface. They can be reused or transferred without fear of damage at least a dozen times. A corrosion resistant flat washer is included to provide a smooth bearing surface for the nut. Never worry about snapping another corroded exhaust stud again. The peace of mind is worth the cost alone.
NOTE: Set includes one stud, locknut, and washer. 12 required for 6 cylinders. Not for use with thick flange manifolds. |
|
PEL-CSP-EXS | Non-corrosive exhaust stud, locknut and washer set (M8 X 22mm, kit of 12, enough for one 6 cyl) [More Info] | Temporarily unavailable | |
Cylinder Head Temperature Sensor |
| You've spent so much time and effort in your rebuild, you might as well change out that old cylinder head temperature sensor, you'll be glad you did! |
|
| 930-606-915-00-M14 | Cylinder Head Temperature Sensor, 911 (1984-89)
Brand: Bosch [More Info] |  |
| $82.50 |  |
Valve Cover Gasket Kits |
| These gaskets should be replaced every time that you adjust your valves. The gasket kits come complete with valve cover gaskets and enough nylock nuts and crush washers for all 4 valve covers. Buy an extra pair or two to have on hand for next time you adjust your valves! |
|
| 10-0906-091-M260 | Valve Cover Gasket Kit (includes Cover Nuts & Washers), 911/911 Turbo (1968-89)
Brand: OEM [More Info] | |
| $25.50 | |
| 10-0906-092-M260 | Valve Cover Gasket Kit with Silicone Bead on lower Gasket 911/911 Turbo (1968-89)
Brand: OEM [More Info] | |
| $34.50 | |
| 930-105-194-04-M17 | Upper Valve Cover Gasket, 911/911 Turbo (1974-89)
Brand: Victor Reinz [More Info] | |
| $5.00 | |
| Lower Valve Cover Gasket, 911/911 Turbo (1974-89) |
| 930-105-195-07-M127 | Lower Valve Cover Gasket, 911/911 Turbo (1974-89)
Brand: German [More Info] | |
| $6.75 | |
| 930-105-195-07-M260 | Lower Valve Cover Gasket, 911/911 Turbo (1974-89)
Brand: OEM [More Info] | |
| $6.50 | |
| Silicone Valve Cover Gaskets |
Silicone Valve Cover gaskets for your Porsche! They are a tad thicker than ones you replace every time you adjust your valves and can get rid of those troublesome leaks. These can be reused again and again; just rinse them off and put them back on.
We do recommend you replace the Nylock nuts each time you remove the valve covers, but that applies to any valve cover gasket. |
|
PEL-SIL-VLGK | Silicone Valve Cover Gasket set, 4 per set, hardware not included - 911 (1968-89), 911 Turbo (1976-92) [More Info] | $38.70 | |
| 900-084-004-03-M58 | Nylock Nut (M8, 34 required), 911 (1965-89), 911 Turbo (1976-92), each
Brand: OEM [More Info] | |
| $0.50 | |
| 900-031-014-30-M131 | Washer 8.4mm (34 required), 911 (1965-89), 911 Turbo (1976-92), each
Brand: Fischer & Plath [More Info] | |
| $0.25 | |
| 900-123-118-30-M131 | Oil Drain Plug Seal (22 X 27mm), Sealing Ring for Plug at Bottom of Engine Sump Plate or Oil Tank, 911/911 Turbo (1965-89), Air Box Sealing Ring, 911 (1974-83), each
Brand: Fischer & Plath [More Info] | |
| $0.25 | |
