| Porsche 911 & Carrera Oil Circulation - Page 11 |
Valve Cover Gasket Kits |
| These gaskets should be replaced every time that you adjust your valves. The gasket kits come complete with valve cover gaskets and enough nylock nuts and crush washers for all 4 valve covers. Buy an extra pair or two to have on hand for next time you adjust your valves! |
|
 10-0906-091-M260 | Valve Cover Gasket Kit (includes Cover Nuts & Washers), 911/911 Turbo (1968-89) Brand: OEM [More Info] |  |
| $21.25 |  |
 10-0906-092-M260 | Valve Cover Gasket Kit with Silicone Bead on lower Gasket 911/911 Turbo (1968-89) Brand: OEM [More Info] |  |
| $33.25 |  |
 930-105-194-04-M17 | Upper Valve Cover Gasket, 911/911 Turbo (1974-89) Brand: Victor Reinz [More Info] |  |
| $5.25 |  |
| Lower Valve Cover Gasket, 911/911 Turbo (1974-89) |
 930-105-195-07-M127 | Lower Valve Cover Gasket, 911/911 Turbo (1974-89) Brand: German [More Info] |  |
| $6.50 |  |
 930-105-195-07-M260 | Lower Valve Cover Gasket, 911/911 Turbo (1974-89) Brand: OEM [More Info] |  |
| $6.25 |  |
| Silicone Valve Cover Gaskets |
Silicone Valve Cover gaskets for your Porsche! They are a tad thicker than ones you replace every time you adjust your valves and can get rid of those troublesome leaks. These can be reused again and again; just rinse them off and put them back on.
We do recommend you replace the Nylock nuts each time you remove the valve covers, but that applies to any valve cover gasket. |
|
 PEL-SIL-VLGK | Silicone Valve Cover Gasket set, 4 per set, hardware not included - 911 (1968-89), 911 Turbo (1976-92) [More Info] | $38.70 |  |
 900-084-004-02-M58 | Nylock Nut (M8, 34 required), 911 (1965-89), 911 Turbo (1976-92), each Brand: OEM [More Info] |  |
| $0.25 |  |
 900-031-014-30-M131 | Washer 8.4mm (34 required), 911 (1965-89), 911 Turbo (1976-92), each Brand: Fischer & Plath [More Info] |  |
| $0.25 |  |
 900-123-118-30-M131 | Oil Drain Plug Seal (22 X 27mm), Sealing Ring for Plug at Bottom of Engine Sump Plate or Oil Tank, 911/911 Turbo (1965-89), Air Box Sealing Ring, 911 (1974-83), each Brand: Fischer & Plath [More Info] |  |
| $0.25 |  |
Gauges & Sending Units |
| Make sure that your oil system is working properly by keeping your electrical sending units and gauges in good working order. Faulty gauges can give you false readings which can jeopardize the health of your engine in an emergency. Having good working gauges is cheap insurance against loss of oil pressure (full engine rebuild). |
|
| Numeric Oil Temperature Gauge Upgrade |
| The early 911s in this series shipped with a temperature gauge that had distinct numbered readings on it. For some reason, this was dropped with the later cars. 'Downgrade' to the earlier style gauge and gain the ability to read your engine temperature accurately. Adding this gauge half to your combo gauge is a simple process, but also requires you to replace your temp sender with the earlier style one. |
|
 PEL-911-TMP-KT1 | Numerical Oil Temp Gauge Kit with Sender and Gauge, 911 (1974-89) [More Info] | Temporarily unavailable | |
 901-641-632-00-M100 | Temperature Sending Unit, for numbered gauge (requires 1 900-123-007-30 sealing ring), 911 (1974-76) Brand: Genuine Porsche [More Info] |  |
| $36.00 |  |
 900-123-007-30-M131 | Sealing Ring (for above sender, 14 x 18mm) Brand: Fischer & Plath [More Info] |  |
| $0.25 |  |
| Mechanical Oil Pressure Gauge Block |
| This convenient and accurate gauge makes fine tuning the engine a bit easier on your 911. Range: 0-100PSI, 0-7 Bar. 1 1/2" Dia. Replaces Porsche P/N 911-107-704-00. Includes Seal rings (3). |
|
 PEL-PBSCECZZN | Mechanical Oil Pressure Gauge Block, includes 3 seal rings, 911/911 Turbo (1974-89) [More Info] | $85.00 |  |
 911-606-230-00-M85 | Oil Pressure Switch, 911 & Turbo (1969-89), Each Brand: Facet [More Info] |  |
| $5.00 |  |
 021-919-081D-M85 | Oil Pressure Switch for Warning Light, 912E, Each Brand: Facet [More Info] |  |
| $4.25 |  |