| Porsche 911 Seats, Belts & Upholstery - Page 2 |
Shoulder Seat Belt Pads |
| Seat belt digging into you a little too much? One solution is to add a wrap-around pad to your shoulder belt. We have a few varieties to offer you - from the somewhat subtle charcoal grey, to the bright red MOMO belt pad - you take your pick. The standard pads are soft velour with Velcro attachments on the underside. The MOMO pads are similar, only with more of a cotton fabric - rather than the velour, and they say MOMO on them! |
|
| PEL-PP-801040 | Universal Fit Shoulder Seat Belt Pad, Black (2 per car, sold individually) 912 (1965-69), Each [More Info] | $8.99 |  |
| PEL-PP-801041 | Universal Fit Shoulder Seat Belt Pad, Charcoal (2 per car, sold individually) 912 (1965-69), Each [More Info] | $9.95 | |
MO-R1742BLU | MOMO Shoulder Seat Belt 2-inch Pad (2 pads), Blue [More Info] | $26.95 | |
| MO-R1742YEL | MOMO Shoulder Seat Belt 2-inch Pad (2 pads), Yellow [More Info] | $26.95 | |
Seat Belt Buzzer Silencer |
| Do you have a racing harness seat belt installed for track days and become annoyed at the alarm buzzing because the standard belt isn't buckled? Click in this temporary seat belt buckle and silence the buzzer. IMPORTANT NOTE: This device is to be used ONLY when using a different seat belt system. |
|
TQJK-BELT | Seat Belt Buckle to Silence Buzzer (for track use only), Each
Brand: Aftermarket [More Info] | $24.95 | |
Harness Mounting Brackets |
| These brackets have been specially designed to allow you to install both, factory seat belts and aftermarket harnesses at the same time. Intended for the use of quick disconnect lap belts on both sides of the seat. This is a perfect set up for your street/track car. All brackets are designed to attach to the factory seat belt mounting locations so no drilling is required. Note: Product is sold individually. |
|
REN-SA01 | Rennline Harness Mounting Bracket, Tunnel Side, Long, Porsche 911/964/993/996/997/944/928/914, each [More Info] | $36.00 | |
REN-SA02 | Rennline Harness Mounting Bracket, Tunnel Side, Short, Porsche 911/964/993/996/997/944/928/914, each [More Info] | $36.00 | |
REN-SA03 | Rennline Harness Mounting Bracket, Driver Side, Porsche 911/964/993/996/997/944/928/914, each [More Info] | $36.00 | |
Harness Bars |
| Weltmeister Harness Bar |
| Made from thick-wall, large 1½" diameter roll bar tubing, for the extra-strength you’re looking for. Weltmeister™ harness bars are finished in durable rich-looking powder-coated black finish that adds a long-lasting factory-style appearance to your interior. Each harness bar has guides to keep your shoulder harness belts in place. Note: There is no front seat movement restriction in the 911 bolt-in harness bars — even for taller drivers! |
|
PEL-910185 | Weltmeister Harness Bar, Coupe, 911 Carrera 2/4 (1989-98), 911 Turbo (1989-98), Each [More Info] | Temporarily unavailable | |
PEL-915614 | Weltmeister Harness Bar (Satin Finish Stainless Steel), Targa, 911/911 Turbo (1974-93) [More Info] | $479.99 | |
| Brey-Krause Harness Bars |
| Brey-Krause harness bars not only guide the driving harnesses, but allow them to be mounted directly to the bar. Their bars are easy to install and remove, use only existing holes and mounting points, and will not damage the car in any way. |
|
BK-R-1010 | Brey-Krause Harness Guide Bar - 911 Coupe (1974-98) [More Info] | $332.80 | |
BK-R-1015 | Brey-Krause Harness Guide Bar - 911 Targa (1974-1993) [More Info] | $436.80 | |
In response to the many requests from Porsche drivers looking for a harness guide bar that would not only guide their driving harnesses, but also allow them to mount their harnesses directly to the bar, we developed the "Harness Truss". The Harness Truss has been tested and certified to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. It's strong, yet it weighs only a fraction of what a support of the same strength made from tubular or bar steel would weigh. The Harness Truss is precision water-jet machined for a perfect fit into Porsche factory mounting points. This type of machining is accurate and does not create heat effected areas in the metal which can alter tensile strength.
Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. A mount really can't be relied on unless it has been tested to support the loads required by the National Highway Traffic Safety Administration.
Material: 6061-T6 aluminum skeleton and reinforcing bar. Type 304 stainless steel brackets.
Finish: Anodized aluminum with satin stainless mounting brackets.
Weight: 9.44 lbs.
Models: 911 Coupes '74 - '98
Installation: Bar attaches to factory mounting points in "B" pillars.
Miscellaneous: Harness Truss is designed to allow enough seat travel for tall drivers. The stainless steel mounting brackets can be left installed in the "B" pillars to easily remove and remount the bar in minutes. R-9018 Adapter Bracket - is available to attach Brey-Krause seat brace
Models: R-9019 or R-9020. |
|
BK-R-1025 | Brey-Krause Harness Truss - 911 Coupe (1974-98) [More Info] | $619.76 | |
