| Porsche 911 Clutch & Flywheel - Page 4 |
Throw Out Bearings & Parts  |
| Throw Out Bearings |
| You should always throw out your old throw-out bearing every time that you replace your clutch disc and pressure plate. |
|
| 901-116-081-11-M38 | Throw Out Bearing, 911/912 (1965-69), 914-6 (1970-72), Each
Brand: Sachs [More Info] |  |
| $144.50 |  |
| 911-116-081-02-M38 | Throw Out Bearing, 911 (1970-71), Each
Brand: Sachs [More Info] | |
| $284.25 | |
| 915-116-082-80-M38 | Throw Out Bearing, 911 (1972-73), Each
Brand: Sachs [More Info] | |
| $167.50 | |
| Throw Out Levers |
915-116-713-01-PH | Throw-Out Lever, 911 (1972-74) [More Info] | $134.95 | |
| Throw Out Bearing Guide Tube |
| This is the guide tube that the throw out bearing is placed on. This should be replaced if significant wear is seen from the throw out bearing binding on it. Replacement of this part is cheap insurance against having to do another clutch job. |
|
| 901-116-087-11-M157 | Throw Out Bearing Guide Tube, 911/912 (1965-69), Each
Brand: Rauch & Spiegel [More Info] | |
| $98.00 | |
| 911-116-087-00-OEM | Throw Out Bearing Guide Tube, 911 (1970-71), Each
Brand: Genuine Porsche [More Info] | $101.25 | |
| 915-116-087-03-M157 | Throw Out Bearing Guide Tube, 911 (1972-73), Each
Brand: Rauch & Spiegel [More Info] | |
| $90.50 | |
| Throw Out Arm Bushings |
| Don't forget this small bushing located in the throw-out arm. It is used to center the pivot on the throwout bearing arm. If it fails it can cause the pivot to bend, making it nearly impossible to operate the clutch. |
|
| 901-116-741-01-M260 | Throw Out Arm Bushing, 911/912 (1965-69), Each
Brand: OEM [More Info] | |
| $3.00 | |
| Throw Out Arm Retainers |
| Check to see if this retaining piece is cracked or not. If it's cracked, your throw-out arm may become loose or even fall out later on. This would be a really bad event, forcing you to remove the transmission to replace this $5 piece. |
|
| 901-116-077-01-M100 | Throw Out Arm Retainer, 911/912 (1965-69), Each
Brand: Genuine Porsche [More Info] | |
| $6.50 | |
| Throw Out Bearing Guide Clips |
| These small plastic pieces guide the throw out bearing in the throw-out arm. These should be replaced along with the throw out bearing. |
|
| 901-116-825-11-M260 | Throw Out Bearing Guide Clip (2 per car, sold individually) 911/912 (1965-69), Each
Brand: OEM [More Info] | |
| $4.75 | |
Transmission Main Shaft Seals |
| The Main Shaft seal prevents transmission oil from leaking out the driveshaft into the flywheel/clutch area. This especially gets messy when the flywheel starts swinging oil around like a Texas twister! Avoid this by replacing this seal during every clutch job. |
|
| 113-311-113B-M30 | 901 Main Shaft Seal, 911/912 (1965-71), Each
Brand: Elring Klinger [More Info] | |
| $2.25 | |
| 999-113-182-40-M30 | 915 Main Shaft Seal, 911 (1972-early 1973), Each
Brand: Elring Klinger [More Info] | |
| $9.50 | |
| 999-113-327-40-M30 | 915 Main Shaft Seal, 911 (late 1973), Each
Brand: Elring Klinger [More Info] | |
| $11.00 | |
