|  | | | Porsche 911 & 912 Tools - Page 9 | Fuel Injection Diagnostic Tools | | Digital Air/Fuel Ratio Meter | The LM-2 combines an air/fuel ratio meter, a full-function 32-channel datalogger, and powerful software to deliver a complete tuning workshop for less than the cost of one dyno day. Whether you have a piggy-back fuel controller, race carb, aftermarket ECU, ODB-II tuning software, or a flash/chip programmer, an LM-2 is the tool you need to dial in maximum HP. The meters digital signal processing technology provides data on exactly how rich or lean an engine is running at any load. The LM-2s self-calibrating circuitry also compensates for changes in temperature, altitude, and sensor condition. - Patented Direct Digital Wideband Technology
- Wideband O2 Compatible with ALL fuel types
- Single or Dual Channel Version Available
- OBD-II Scan tool- read/clear DTCs and log up to 16 channels of CAN OBD-II Data
- Log directly to SD card (included)
- Playback log data on screen and/or with powerful LogWorks software (included)
- Large high-contrast graphics LCD
- Built-in RPM converter (direct frequency or with optional inductive clamp)
- 4 fully-differential analog inputs
- 2 configurable linear analog outputs
- Positive lock connectors for all connections
- Innovate MTS serial IN and OUT
- USB connection to your PC
The LM-2 also features two fully programmable linear analog outputs to connect to analog gauges, dyno computers, ECUs, piggyback controllers, and other devices with analog inputs. Analog output 1 comes setup from the factory ready for narrowband simulation; analog output 2 is configured as 0 volt = 7.35 AFR and 5 volts = 22.39 AFR. With the provided LM Programmer software these analog outputs may also be configured by the user.
The LM-2 Kit (Single Wideband O2) includes the LM-2 meter, Bosch wide-band oxygen sensor, 10 ft sensor cable, cigarette-lighter power adapter, analog in/out cable, ODB-II/CAN interface cable, SD memory card, USB cable for PC connection, weld-in bung and plug, LogWorks software CD, and quick-start guide. Carrying Case also included!
More accessories for your LM-1 available here.
For permanently installed tuning solutions, click here.
Manufacturer: Innovate Motorsports
Click here to visit the manufacturer's home page. |
| 
INN-3806 | Innovate Motorsports LM-2: Digital Air/Fuel Ratio Meter [Photo] [Photo] | $479.00 |  | Pelican Engine Rebuild Super Tool Kits | There are some specialized tools that are essential to the proper rebuild of your engine. The Pelican Super Tool Kit contains all of the following tools:- 5-Arm Engine Mount Stand
- Camshaft Holding Bar
- 46mm Crowsfoot Wrench for Camshaft Nut Removal (through 1980)
- Z-Block Holder for Dial Gauge
- Flywheel Bolt Tool
- Flywheel Lock
- Chain Tensioner Tool
- Piston Hold-Down Tools (6)
- Ring Compressor Tool
- Valve Adjustment Tool
- Heat Exchanger Barrel Nut Removal Tool
- Set of Six Acid Brushes
Engine Rebuild Tools are NON-RETURNABLE items. |
| | PEL-REBKT-13N | Pelican Engine Rebuild Super Tool Kit (1965-1980 1/2) | $565.35 | | | PEL-REBKT-14N | Pelican Engine Rebuild Super Tool Kit (1980 1/2-1989) | $542.85 | | Stud Removal Tools | | This tool incorporates a collet that latches onto and compresses the threads of the stud, squeezing them tight. Then the tool and the stud can be removed. If you are removing studs from an engine case, an extra vise-grip or two might be useful as well to get more torque on the studs. |
| | PEL-SNAPON-CG500-2 | Snap-On Stud Remover Collet Tool | $85.75 | | | PEL-SNAPON-CG500-43 | Snap-On Stud Remover Collet, M10x1.5 | $41.45 | | | PEL-SNAPON-CG500-37 | Snap-On Stud Remover Collet, M8x1.25 | $41.45 | | Dremel 83pc Variable Speed Moto-Tool Kit | Cut, grind, carve, rout, sharpen, drill, polish, or sand. If you can dream it, you can do it with the MultiPro kit. Combining the correct speeds and bits, you can complete all kinds of tasks on a multitude of materials.
Variable speed, from 5,000 to 35,000 rpm
Quick-change collet
Flexible shaft attachment, 75 bits, and two clamps
2-year warranty
The kit includes the MultiPro tool, convenient case with storage compartments, wrench, 75 bits, flex shaft, two clamps, the Dremel chuck, garden tool sharpening attachment, and a book of 175-plus uses for the MultiPro kit.
Manufacturer: DREMEL
Click here to visit the manufacturer's home page |
| 
TOL-DRE3956-02 | 83pc Variable Speed Moto-Tool Kit [Photo] | $135.75 | |
| |
|
|
|
