| Porsche 911 Tools - Page 8 |
Tie Rod Tools |
PEL-TOL-P1014 | Tie Rod End Puller, 911 (1965-89), 914 All, 912 [More Info] | $71.40 |  |
Factory Timing Belt Tensioning Tool |
| The tool below are all that's needed to take the guess work out of properly adjusting your timing and balance shaft. The belts must be done every 15,000 miles and doing to is the only way to ensure long engine life. If your going to keep the car, you might as well day, or you will want to see the car after a services. The Tensioning tool is Made in Germany, same tool the factory technicians use. Comes with a factory 2 year Limited Warranty.944 Balance Shaft Locking Bar - The balance shaft locking bar is used during the timing belt replacement process on 944s. It is designed to keep the balance shaft sprocket from turning while removing/replacing the retaining bolt.Timing Belt Adjusting Tool-This specially designed tool makes adjusting the timing belt a snap. Balance Shaft Belt Gauge - This tool has also proved invaluable to properly adjust the roller for the balance shaft toothed belt. |
|
000-721-920-10-OEM | Factory Timing Belt Tensioning Tool, 944 (3/1983-89), 924S/944S (1987-88), 944S2 (1989-91), 944 Turbo (1986-89), 968 (1992-95)
Brand: Genuine Porsche [More Info] | $600.75 | |
PEL-TOL-P232 | Aftermarket 944 Balance Shaft Locking Bar [More Info] | $47.00 | |
000-721-920-00-OEM | Factory 944 Balance Shaft Locking Bar
Brand: Genuine Porsche [More Info] | $120.00 | |
000-721-920-12-OEM | Calibration Bar
Brand: Genuine Porsche [More Info] | $32.00 | |
000-721-920-70-OEM | Balance Shaft Belt Gauge
Brand: Genuine Porsche [More Info] | $26.50 | |
Timing Sprocket Registration Pin Puller |
PEL-STSK-SR026 | Stomski Racing Sprocket Registration Pin Puller, each, 911 (1965-98) [More Info] | $34.80 | |
Synchrometer |
| Synchronizing your Porsche mechanical fuel injection or carburetors with our tool, is the only way to precisely measure the air intake for optimum power and a smooth idle. |
|
PEL-TOL-STESK | Mechanical Injection/carburetor Synchrometer [More Info] | $55.80 | |
Float Gauge |
PEL-PMO-004 | Float Gauge by PMO, for Weber and Zenith 3-bbl carbs [More Info] | $34.00 | |
Allen Head Tools |
| Removing your 911 heads or heat exchangers can be very difficult without the correct tools for the job. With these extra long Allen extensions, those nuts can't hide. The 10mm tool is used for removing and tightening the head studs on the 911 motor. The 8mm tool is used to remove and tighten the 911 heat exchanger nuts. |
|
PEL-TOL-A10MM | Allen Head Nut Removal Tool for 911 Head Studs (10mm) [More Info] | $44.99 | |
PEL-TOL-P243 | Allen Heat Exchanger Nut Removal Tool (8mm) [More Info] | $29.40 | |
Magnetic Box "V" Wrench (17mm) |
| This unique-looking tool is used to aid in the removal of the engine/transmission bolts. The V-Wrench holds the nut on the other side of the engine compartment so that you can remove the nut from the transmission. The V design holds the nut steady, unlike a normal wrench, and allows you to remove the bolt on the other side without the help of an assistant. |
|
PEL-TOL-P222 | Magnetic Box "V" Wrench (17mm) [More Info] | $31.00 | |
Suspension Alignment Tools |
| Doing some adjustments to your suspension? Using the right tools can help you obtain exactly the values that you are looking for. |
|
PEL-TOL-P221 | Rear Suspension Toe-In Adjuster, 911 All [More Info] | $26.80 | |
PEL-TOL-P235 | Camber Adjuster, 911, C2 and C4 [More Info] | $21.60 | |
