| Porsche 911 Engine Miscellaneous - Page 4 |
Tools |
| Engine Stand Adapter Ring |
This Engine Stand Adapter Ring will easily bolt onto any universal engine stand, using four 3/8" bolts, giving you a safe and easy way to work on any 356 to 930 Porsche engine. This is a very heavy-duty piece that is machined from solid steel, with all the right notches and relief angles to accommodate all Porsche and VW air cooled engines.
NOTE: Universally adjustable adapter not included with ring. These come with most engine stands available here. |
|
PEL-TOL-MCDENG | Engine Stand Adapter Ring for Porsche and VW air-cooled engines [More Info] | $145.00 |  |
| U-Base Engine Stand |
• Heavy duty mounting plate and adapter arms for servicing light truck and car engines
• Heavy-duty four wheeled base increases stability
• Wide 'mouth' base opening works with most mobile engine cranes
• Fixed polyurethane back wheels; poly swivel castors on front for smooth travel
• 24" handle makes easy work of rotating the engine 360 degrees; hitch pin locks engine in place
• Built-in tool tray keeps frequently needed tools right close to work area
• OTC 2 year warranty
Manufacturer: OTC DIVISION OF SPX CORP
Click here to visit the manufacturer's home page
Not exactly what you're looking for? Check out the rest of the selection here! |
|
TOL-OTC2012A | U-Base Engine Stand - 1250 lbs [More Info] | $195.50 | |
| Engine Yoke Securing Nuts |
| Finally, a clean and elegant way to secure your 911 engine to the factory-style yoke - no more sockets, washers, and oversized nuts to take up slack. Use these knurled nuts and adapters to mount the different length engine case studs to the yoke. Not only will you no longer need to hunt for the right combination of hardware to fit, but with the built-in clearance of these stainless steel nuts and adapters, you will be able to easily install and remove flywheels and clutch assemblies while the engine is on the stand! |
|
STOMSKI-SR028 | Stomski Racing Engine Yoke Securing Nut/Adapter Set, for Porsche engine stand fixtures (P201) [More Info] | $47.50 | |
| Engine Test Stand |
| Run your motor BEFORE installation to troubleshoot and tune. This test stand is compatible with all 911/930 (1965-86), 912, and 914 air-cooled motors Kit includes: starter adapter ring, stand with rear cross member supports, 1.1L Fuel cell, battery cables, and starter control box with wiring harness. (Electric fuel pump, starter, battery and oil tank not included.) Stand disassembles for easy storage and shipping. |
|
ZLX-ENG-STND | Engine Test Stand for 911/930 (1965-86), 912, 914 air-cooled motors [More Info] | $629.00 | |
| Flywheel Socket |
| Get the correct socket to remove/install those Flywheel Bolts! |
|
TOL-SK41422 | Flywheel Bolt Socket Tool, 12-Point/12mm [More Info] | $21.95 | |
| Oil Seal Installation Tools |
| When rebuilding your motor, do the job right with our oil seal installation tools. Designed to perform an installation that is perfectly aligned with the case, these installation tools will guarantee a leak-free seal, without damaging your valuable case. |
|
PEL-TOL-P215 | Oil Seal Installation Tool for 911 (1965-77), Flywheel Side [More Info] | $108.40 | |
PEL-TOL-P234 | Oil Seal Installation Tool for 911 (1978-94), Flywheel Side [More Info] | $129.30 | |
PEL-TOL-P216 | Oil Seal Installation Tool for 911 (1965-89), Pulley Side [More Info] | $53.70 | |
| Metric Dial Indicator Gauge |
| A must for every Porsche owner, this metric dial gauge is not only useful, but it's also cool looking too! 0-10MM travel. Measures in 100ths of a millimeter. All steel and brass construction. Resettable pointers. Use with any standard holder. The Metric Dial Gauge is a requirement for setting the sensitive timing adjustment of the cams when rebuilding a 911 motor. It's also essential when measuring the flywheel and crank shaft end play. The Z-block fixture is designed to hold the dial gauge while adjusting the 911 camshaft timing, and also comes with a dial gauge extension pin. The Dial Gauge Holder is designed to hold the gauge while measuring flywheel and pulley end play. |
|
TOL-721-T63 | Metric Dial Gauge [More Info] | $79.00 | |
PEL-TOL-P207 | Dial Gauge Holder (Z Block), w/extension Pin [More Info] | $36.10 | |
PEL-TOL-P240 | Dial Gauge Holder [More Info] | $35.20 | |
