| Porsche 356 Tools - Page 2 |
Porsche Engine Rebuild Stand |
| Engine Yoke Securing Nuts |
| Finally, a clean and elegant way to secure your 911 engine to the factory-style yoke - no more sockets, washers, and oversized nuts to take up slack. Use these knurled nuts and adapters to mount the different length engine case studs to the yoke. Not only will you no longer need to hunt for the right combination of hardware to fit, but with the built-in clearance of these stainless steel nuts and adapters, you will be able to easily install and remove flywheels and clutch assemblies while the engine is on the stand! |
|
STOMSKI-SR028 | Stomski Racing Engine Yoke Securing Nut/Adapter Set, for Porsche engine stand fixtures (P201) [Photo] | Temporarily unavailable | |
12-Point/12mm Flywheel Socket |
| Get the correct socket to remove/install those Flywheel Bolts ! |
|
TOL-SK41422 | Flywheel Bolt Socket Tool, 12-Point/12mm [Photo] [Photo] | $16.00 |  |
Heavy Duty Flywheel Lock |
| Getting ready to remove that flywheel? You're going to need this heavy duty flywheel lock. Makes that job so much safer and easier! |
|
PEL-UN1201100 | Flywheel Lock, 911 (1965-73), 912 (1965-69) 914 All [Photo] | $16.15 | |
Oil Filter Wrenches |
| Get off easily with our new oil filter wrench! This wrench attaches directly to the top of the oil filter and allows you to attach a standard 3/8" drive ratchet to remove the filter. Gone are the days of poking messy holes in the filter just to get a screwdriver in there to remove it from the oil tank. |
|
PEL-PP903124 | Oil Filter Removal Socket Wrench Tool - 911/C2/C4 (1965-94), 911 Turbo (1976-89) [Photo] | $10.10 | |
Transmission Drain Plug Removal Tool |
| The 901/915 and 930 transmissions used a large 17mm hex key nut as both the filler and the drain plug for the transmission. You need this tool to easily drain and refill your transmission oil. Fits all models of the 914 and 911/912 (thru 1986), 911 Turbo (1976-88), 924S/944, and 928. The tool is designed to fit on a 1/2 or 3/8 inch socket wrench, and can be used for a variety of other reasons too. Note: WILL NOT FIT the 911 (1987-89), 911 Turbo (1989) with the G-50 transmission. |
|
PEL-DPR-5773 | Transmission Drain Plug Removal Tool (3/8 inch drive) [Photo] | $9.65 | |
PEL-DPR-1017 | 17mm Transmission Drain Plug Removal Tool (1/2 inch drive) [Photo] | $25.00 | |
Hub/Bearing Extractor and Installer Kit  |
| Want to save on a costly repair, replace your own bearing or pull your own hubs with our all in one Porsche kit. Designed to efficiently remove and install hub and wheel bearings, this kit will make the notoriously difficult job of removing rear wheel bearings a breeze. The kit comes with a set of adapters specific to the Porsche series, but can also be used on all front and rear wheel drive vehicles with independent suspension. Also for R&R of the rear wheel bearings only on models with drum brakes independent rear suspension. |
|
| PEL-TOL-SIRB90-P1 | Hub/Bearing Extractor and Installer Kit, 911 1965-73, 912 All, 914 All | $166.00 | |
Oil Seal Installation Tools |
| When rebuilding your motor, do the job right with our oil seal installation tools. Designed to perform an installation that is perfectly aligned with the case, these installation tools will guarantee a leak-free seal, without damaging your valuable case. |
|
PEL-TOL-P215 | Oil Seal Installation Tool for 911 (1965-77), Flywheel Side [Photo] | $113.00 | |
PEL-TOL-P216 | Oil Seal Installation Tool for 911 (1965-89), Pulley Side [Photo] | $56.00 | |
PEL-TOL-P231 | Oil Seal Installation Tool for 944, Balance Shaft [Photo] | $40.00 | |
PEL-TOL-P218 | Oil Seal Alignment Tool for 944 (1983-86) [Photo] | $20.00 | |
PEL-TOL-P212 | Oil Seal Arbor - Crank Seal (flywheel side), each, 356 all, 912 (1965-69) (not for 914) [Photo] | $44.00 | |
