| Porsche 356 Pistons, Cylinders, and Heads - Page 2 |
Piston Rings |
| Piston rings act to create a sealed chamber for compression and also to control oil flow inside a cylinder. When replacing piston rings, have your cylinders honed to ensure proper seating of the rings. |
|
PEL-DE1358 | Piston Ring Set (82.5 3x3x5), 356B/356C (1957-65), from eng# P67000, 356 Super from eng# P81200 [Photo] | $58.20 |  |
PEL-DE1359 | Piston Ring Set (82.5 2x2x2x5), 356B/356C (1957-65), from eng# P67001, 356 Super from eng# P81201 [Photo] | $62.40 | |
616-103-907-05-M42 | Piston Ring Set, Standard (82.50 mm) 356C (1964-65)
Brand: Goetze [Photo] [Photo] |  |
| $23.25 | |
Valve Guides  |
| You should always replace your guides when rebuilding your heads. The newer style valve guides are highly reliable, reduce friction and wear, and they look real cool too. |
|
616-104-321-00-M105 | Valve Guide (Intake, sold per each), 356B Super 90, (1960-63)
Brand: Canyon [Photo] [Photo] | |
| $6.00 | |
616-104-322-00-M105 | Valve Guide (Intake/Exhaust, sold per each), 356A/B/C (1950-65) (except Super 90)
Brand: Canyon [Photo] [Photo] | |
| $7.00 | |
Valve Springs |
| When rebuilding your heads, you should always replace the springs. We have seen broken springs come close to destroying a recently rebuilt motor. New springs are inexpensive insurance against catastrophic failure. |
|
616-105-432-03-M260 | Valve Spring (Intake/Exhaust, sold per each), 356A/B/C (1950-65)
Brand: OEM [Photo] | |
| $12.50 | |
Valve Stem Seals |
| These are the small seals that mate at the top of the valve stem. They act to keep oil from leaking into the cylinder. If you have a small amount of white smoke while starting your car in the morning, it could be bad stem seals. |
|
616-105-491-02-M30 | Valve Stem Seal (sold per each, 8 required), 356A/B/C (1950-65)
Brand: Elring Klinger [Photo] [Photo] | |
| $1.25 | |
Valve Cover Gaskets |
| These gaskets should be replaced every time that you adjust your valves. You should also put a little gasket sealer on the inside of the cover where the gasket mounts to the cover. This should prevent the oil leaks that sometimes occur when there isn't a really good seal. Buy an extra pair or two to have on hand next time you adjust your valves! |
|
616-104-951-00-M42 | Valve Cover Gasket (sold per each, 2 required), 356A/B/C (1950-65)
Brand: Goetze [Photo] [Photo] | |
| $5.50 | |
Valve Keepers |
| These are the little pieces that hold the valve in place by the tension of the valve spring. |
|
113-109-651A-M36 | Valve Keeper, (sold per each, 16 required), 356A/B/C (1950-65)
Brand: Febi [Photo] | |
| $3.00 | |
Valve Adjusting Screw |
369-05-243-M260 | Adjusting Screw for Rocker Arm (8 per car, sold per each), 356 (1956-65), 912, Each
Brand: OEM [Photo] | |
| $7.75 | |
