Pelican Parts
BMW Parts Catalog Accessories Catalog BMW How To Articles BMW Tech Forums
Call Pelican Parts at 888-280-7799
1994 BMW 325i Base Sedan
 
 
Tool Catalog
Toolkits & Tools - Factory
Floor Jacks
Jack Pads
AC Hydraulic Jacks
Hydraulic Jack Oil
Jack Stands
Tool Boxes & Trays
Creepers
Wrenches
Fan Clutch Wrenches
Torque Wrenches
Torque Wrench Inserts
Bit Sets
Screwdrivers
Sockets
Pliers
Hammers and Mallets
Diagonal Cutters
Center Cutters
Cable Cutters
Bolt Cutters
Pry Bars
Breaker Bars
Snips and Cutting Tools
Chisels
Rivet Tools
Work Lights
Flashlights
Vises
Jump Starter
Code Scan / Reset
Peake Research Code Scan
Peake Research SRS Reset
Diagnostic Scanners
Electronic Diagnostic Tools
Air/Fuel Ratio Meters
WEGO IV Air/Fuel Tuning
K&N Air/Fuel Monitor
Jack Pads
Lug Nut Sockets
Clutch Alignment Tools
Clutch Tools
Engine Stands
Engine Tools
Valve Spring Compressors
Valve Keeper Tools
Flywheel Locks
Leakdown Testers
Compression Testers
Oil System Tools
Timing Chain Tools
Timing Lights
Pulley Tools
Cylinder Head Tools
Piston Ring Compressors
Camshaft Tools
Cam Timing Tools
Stud Removal Tools
Spark Plug Tools
Oil Filter Tools
Oil Drain Pans
Drain Plug Tools
Dial Indicators
Gasket Remover
Cooling System Tools
Oxygen Sensor Removal
Suspension Tools
Wheel Bearing Puller
Spring Compressors
Ball Joint Tools
Bearing Tools
Control Arm Tools
Alignment Tools
Smart Racing Alignment Tools
Grease
Lubricants
Strut Mount Tools
Emergency Bumper Set
Axle Shaft Tools
Transmission Tools
Transmission Drain Plug Tools
Panel Removal Tools
Brake Tools
Caliper Tools
Brake Fluid Testers
Brake Bleeder Valves
Speed Bleeders
Power Bleeder
Brake Bleeding
Mirrors and Magnets
Thermometers
Dashboard Tools
Disassembly Tools
Radio Removal Tools
Airbag Tools
Pullers
Hose Removal Tools
Anti-Seize Products
Assembly Paste
Service Covers
Mats
Safety Glasses
Ear Protection
Latex and Nitrile Gloves
Work Gloves
Respirators & Masks
Media Blaster Machine
Parts Cleaners
Hand Cleaner
Hand Wipes
Towels and Rags
Multimeters
Refractometers
Electrical Wiring Tools
Soldering
Electrical Tape
Heat Shrink Tubing
Heat Guns
Wire Connectors
Air Blow Guns
Spray Bottles
BMW Home > 1994 BMW 325i Base Sedan > Tools & BooksTools  

Tools

- Page 11

Clutch Tools

Pressure Adaptor needed for pressuring the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Comes with a 1/4-18 NPT threaded opening. Applicable to most European models.

Designed to extract bearings and bushings with an I.D. of 12mm up to 15mm.


These odd-shaped sockets are required to remove some of the bolts that connect the engine to the transmission. Seven sizes E-6 through E-16. The three smaller sizes are 1/4" drive; the four larger sizes are 3/8" drive. Made of heat-treated alloy steel. Sockets are kept in a convenient vinyl holder. Includes External Torx Sockets: E6, E7, E8, E10, E12, E14, and E16.

Engine Stands


Engine Stand - 1000 lb. Capcity  
 
[ More Info ]

Note: A timesaver for passenger car and light truck engine rebuilding or repair. Four adjustable attachment arms make engine mounting fast and easy. Engine can be rotated a full 360 degrees with a turn of the handle; a locking pin secures the work in any of eight positions. Two rear wheels lock tightly to anchor the stand in place. Easy one-bolt disassembly for transport, Item not stocked in our warehouse; special order only.~Contact your sales representative for details.

OTC
Engine Stand (Yoke Portion)  
 
[ More Info ]

Note: For Porsche 911 air cooled engines & 996 Turbo, Also available mount/pinch clamp #313.

Baum Tools
Brand Rating
$592.50
Engine Stand (Yoke Portion)  
 
[ More Info ]

Note: Also available mount/pinch clamp #313, For Porsche Boxster/Cayman 1997-2008 & 911 Carrera 1999-2008.

Baum Tools
Brand Rating
$1151.75

Engine Tools

These specialty tools are designed for use specifically with your vehicle. If you are opting to save money by working on your car yourself, it is a very wise investment to have the proper tools. Some tasks may be nearly impossible to perform without the specific tool designed to assist you in the process.


Secures the water pump hub from rotating during R&R of fan clutch nut.


Valve Spring Compressors
With this latest evolution to our Universal Valve Spring Tool we have added the ability to actuate the compression tube even in tight confined locations like under the cowl where the lever cannot be moved or may not even fit. By adding the ability to separate the lever from the compression tube anywhere along the bar you can compress the springs that are confined by brake boosters, AC housings or other factors by locating the lever along the bar where there is open space.

  • Access to valves in areas that are not in open areas with engine in vehicle
  • Valve springs can be depressed "remotely", depressor bar and compression tube are separate
  • Complete universal kit with multi adjustable points
  • No need to remove engine due to confined areas saving time
  • No other valve spring compressor is as universal and adjustable
  • Depressor tube slides easily to each valve location without changing settings
  • All components store neatly in a blow molded box
Valve Keeper Tools
Valve Keeper Tool  
 
[ More Info ]

Note: Used to easily install valve keepers on intake/exhaust valves. For most engines with 6 mm intake/exhaust valve stems, except the BMW N62 and N63 V8 engines,

AGA
Brand Rating
$199.25
BMW Home  >  1994 BMW 325i Base Sedan > Tools & Books  >  Tools  

  Page 11 of 26  <1.. 910111213.. 26>


Browse Tools for all 3-Series E36 (1992-1999) vehicles

Page last updated: Wed 11/22/2017 01:49:22 AM
QUICK LINKS
About Us
Careers
Pelican Parts, LLC
1600 240th Street
Harbor City, CA 90710
Order Online or Call:
888-280-7799
CONNECT WITH US
NEWSLETTER
Sign Up for Pelican Pit Stop News & Special Offers

Close this window