|  | | | BMW E46 Clutch & Flywheel - Page 1 | This section contains clutches and related items. If you are looking for that little piece to complete your clutch job, you are in the right place. When doing a clutch job, it's always a good idea to replace the rear end seal on the engine at the same time, replace the throw-out bearing, flywheel bolts and pilot bearing. You should also replace the clutch release fork and the master/slave cylinders at the same time for added insurance. If you are re-using your flywheel, have it re-surfaced so your new clutch seats correctly. Please keep in mind that the vehicle designation for the various E46 models differs slightly from the old BMW system. Here is a breakdown of the new models for all of you - i = 4 Door Models
- Ci = 2 Door Models
- iC = Convertible Models
- Xi 4 = Wheel Drive Models
|
| Clutch Super Kits  | Now available from Pelican is our clutch super kit for the E46 BMW. In this kit, you get everything you need to replace your clutch all at once. If you are spending the time and effort to pull your engine out of your car, you might as well make sure that you are replacing and fixing every piece that might need attention, while you have access to it. Here's what the kit includes:- Three piece clutch kit
- New bolts for flywheel and clutch pressure plate
- New crankshaft rear seal (aka flywheel seal)
- New transmission Input Shaft seal
- New shifter selector rod seal
- New exhaust flange gaskets/seals
- New exhaust flanges
- New flex disc nuts (where applicable)
- New pilot bearing
- New release bearing spring clip
- New clutch pivot pin
- New slave cylinder
If you don't already own one, you will also need the flywheel pilot bearing puller tool for removing the flywheel pilot bearing. You will also need the clutch alignment tool as well.
NOTE: Flywheels are not included with these kits. If your old flywheel is worn beyond its re-surfacing limit, it should be replaced with a new one available below. NOTE: Proper installation requires clutch and disc to be installed on the flywheel before removal of shipping plate. Removal of the shipping plate before installation on the flywheel will require the SAC springs to be reset with factory special tools. To remove this plate, you MUST use: (1) CT-1011 Tool, not included in kits. |
| | PEL-SKCKE46-1N | Clutch Super Kit, 323i/Ci/iC (1999-00), Each [More Info] | $494.25 |  | | PEL-SKCKE46-2N | Clutch Super Kit, 325i/Ci/iC (2001-08/03), Each [More Info] | $499.25 |  | | PEL-SKCKE46-3N | Clutch Super Kit, 328i/Ci (1999-00), Each [More Info] | $528.00 |  | | PEL-SKCKE46-4N | Clutch Super Kit, 325Xi (2001-02/03), 330i/Ci/iC (2001-02/03), Each [More Info] | $534.50 |  | | PEL-SKCKE46-5N | Clutch Super Kit, M3 (2001-06), Each [More Info] | $675.75 |  | | CT-1011-M37 | Clutch Installation Tool, for Self Adjusting Clutches ONLY, E46 323i/Ci, 328i/Ci, 325i/Ci (through 8/03), 325Xi (through 2/03), 330i/Ci/Xi (through 2/03) [More Info] |  |
| $16.25 |  |  CT-1014-M37 | Clutch Installation Tool, for Self Adjusting Clutches ONLY, E46 325i/Ci/Xi (from 9/03), 330i/Ci/Xi (from 3/03) [More Info] |  |
| $17.75 |  | Clutch 3 Piece Kits  | | Our 3-piece package includes all original equipment clutch components. Contains New Pressure Plate, New Clutch Disc and a new Throw-out bearing. Save money over the costs of the individual pieces by purchasing the kit in this convenient three-piece package. |
|  21-21-2-282-667-M37 | | $427.25 |  |  21-20-7-551-576-M37 | Clutch Kit, E46 325i/Ci (from 9/03), Each Brand: Luk [More Info] |  |
| $288.50 |  | | Clutch Kit, Self-Adjusting | | NOTE: Proper installation requires clutch and disc to be installed on the flywheel before removal of shipping plate. Removal of the shipping plate before installation on the flywheel will require the SAC springs to be reset with factory special tools. To remove this plate, you MUST use: (1) CT-1011 Tool |
|  21-21-7-523-620-M37 | Clutch Kit, Self-Adjusting, 323i/Ci/iC (1999-00), 325i/Ci/iC (2001-08/03), Each Brand: Luk [More Info] |  |
| $294.50 |  |  21-21-7-515-141-M37 | Clutch Kit, Self-Adjusting, 328i (1999-00), Each Brand: Luk [More Info] |  |
| $309.00 |  |  21-20-7-531-843-M37 | Clutch Kit, Self-Adjusting, 325Xi (2001-02/03), 330i/Ci/iC (2001-02/03) Brand: Luk [More Info] |  |
| $313.75 |  |  21-20-7-531-556-M37 | Clutch Kit, Self-Adjusting, 325Xi (9/03-2005), 330i/Ci/iC (03/03-2005) Brand: Luk [More Info] |  |
| $410.50 |  |  21-20-7-531-844-M37 | Clutch Kit, Self-Adjusting, 330Xi (2001-02/03), NOTE: Proper installation requires clutch and disc to be installed on the flywheel before removal of shipping plate. Removal of the shipping plate before installation on the flywheel will require the SAC springs to be reset with factory special tools. To remove this plate, you MUST use: (1) CT-1011 Tool Brand: Luk [More Info] |  |
| $350.50 |  |  21-21-7-528-211-M37 | Clutch Kit, Self-Adjusting, 330Xi (03/03-2005) Brand: Genuine Luk [More Info] |  |
| $323.50 |  | | CT-1011-M37 | Clutch Installation Tool, for Self Adjusting Clutches ONLY, E46 323i/Ci, 328i/Ci, 325i/Ci (through 8/03), 325Xi (through 2/03), 330i/Ci/Xi (through 2/03) [More Info] |  |
| $16.25 |  |  CT-1014-M37 | Clutch Installation Tool, for Self Adjusting Clutches ONLY, E46 325i/Ci/Xi (from 9/03), 330i/Ci/Xi (from 3/03) [More Info] |  |
| $17.75 |  |
| |
|
|
|