|  | | | BMW E36 Tools - Page 3 | Engine Tools | | Chain Tensioner Tools | | Use this tool in place of the spring-loaded tensioner when timing the camshafts during VANOS installation. It's important to use this tool, and not to rely solely on the spring-loaded tensioner - it does not provide enough tension when the car is sitting to accurate time the camshafts. See how it is used here. |
| 
83-30-0-493-548-BOE | Tensioner Pressure Tool, For BMW S50, M50 and M62 Engines, service manual reference #11 3 390, Each
Brand: Genuine BMW [Photo] | $45.50 |  | | 83-30-0-491-025-BOE | Tensioner Pressure Tool, For BMW M52, M52TU, M54, M56, S52 service manual reference #11 4 220, Each
Brand: Genuine BMW | $67.00 | | 
TOL-BMW3041 | VANOS Air Compressor Adapter, Applicable: BMW engines - M50, M52, M52TU, M54, M56, M62, Each [Photo] | $22.00 | | 
TOL-BMW3042 | VANOS Cam Sprocket Assembly Jig, Applicable: BMW engines - M52TU, M54, M56, Each [Photo] | $99.50 | | 
TOL-BMW3043 | VANOS Cam Shaft Alignment Jig, Applicable: BMW engines - M52TU, M54, M56, Each [Photo] | $203.00 | | 
TOL-BMW3046 | VANOS Rigid Chain Tensioner, Applicable: BMW engines - M52, M52TU, S52, M54, M56, service manual reference #11 4 220, Each [Photo] | $37.00 | | 
TOL-BMW3047 | VANOS Chain Tensioner Lock Pin, Applicable: BMW engines - M50, M52, Each [Photo] | $8.30 | | 
TOL-BMW3055 | VANOS Cam Timing Master Kit w/ case - 5 Piece, Includes BMW3041, BMW3042, BMW3043, BMW3046, and BMW3047, Each [Photo] | $399.00 | | | Flywheel Lock | | This is the correct tool used for locking the crankshaft in the TDC position when adjusting or replacing timing components. |
| 
88-88-6-112-300-BOE | Flywheel Lock, For BMW Engines: M42, M44, M50, S50, M52, S52, M54, S54, M60, M62, S62, M70, M73. Service manual reference # 11 2 300 [Photo] | $28.75 | | | Camshaft Holding Tools | | You need this tool to properly time your camshaft. See how it is used and read our Technical Article on the subject here. |
| 
TOL-3017 | Camshaft Holding Tool/Fixture (includes (2) blocks (1) swivel lock and (1) flywheel locking pin), Fits M42, M44, M50, M52, M54, S50, S52 Engines, Each [Photo] [Photo] | $145.70 | | 
TOL-3035 | Camshaft Holding Tool/Fixture, For BMW V-12 Engines [Photo] | $102.80 | | | Crank Pulley Securing Tools | | These tools bolt to the front of the crankshaft pulley and allow you to secure the engine from turning, allowing you to remove the crank pulley securing nut. |
| 
TOL-3034-1 | Crank Pulley Securing Tool, For M60 and M62 Engines, Each. See BMW service # 11 2 450 [Photo] | $55.80 | | 
TOL-3034-2 | Crank Pulley Securing Tool, For M20, M42 and M50 Engines, Each [Photo] | $47.70 | | 
TOL-3034-3 | Crank Pulley Securing Tool, For BMW M30 Engines, Each [Photo] | $47.70 | | 
TOL-3034 | Crank Pulley Securing Tool Set, Contains All Above Wrenches [Photo] | $136.20 | | | Steering Rack Pin Wrenches | | This wrench is used to remove and install the slotted nut on the steering rack on BMW E30 3 Series models. This tool is required if you are replacing your steering rack seals. |
| 
TOL-3031 | Steering Rack Pin Wrench, For All E30 3 Series Models (1984-92), Each [Photo] | $40.50 | |
| |
|
|
|
