| BMW E39 Specialty Tools - Page 4 |
Clutch Tools |
| You can never perform a good job on repairing your BMW if you don't have the right tool. A lot of people try to cut corners because they either don't have the tool they need, or they don't even know that it exists! Having the right tool for the job saves time, money, and wasted effort. A job that can take 4 hours without the right tool, can take a mere few minutes. You're already saving lots of money by doing the work yourself, spend some money and get the tool that you need. Once it's in your collection, you will not know how you got along without it! |
|
| Torx Female Socket Set |
| These odd-shaped sockets are required to remove some of the bolts that connect the engine to the transmission. Seven sizes E-6 through E-16. The three smaller sizes are 1/4" drive; the four larger sizes are 3/8" drive. Made of heat-treated alloy steel. Sockets are kept in a convenient vinyl holder. Includes External Torx Sockets: E6, E7, E8, E10, E12, E14, and E16. |
|
TOL-LIS26750 | Torx Female Socket Set [More Info] | $20.23 |  |
| Flywheel Bolt Tool, Special T60 Torx Socket |
| This T60 Torx Socket is essential in order to R&R dual mass flywheel bolts of ZMS engines. The bolts are situated off-center to their respective access points. The slimmed-down shaft allows for the socket to line up straight with the bolt. |
|
TOL-BMW3048 | Flywheel Bolt Tool, Special T60 Torx Socket, fits E34 and E39 4.0L and 4.4L V-8s [More Info] | $42.95 | |
| Pilot Bearing Puller |
| Designed to extract bearings and bushings with an I.D. of 12mm up to 15mm. |
|
PEL-TOL-1088 | Pilot Bearing Puller, BMW All [More Info] | $52.90 | |
| Clutch Alignment Tools |
PEL-TOL-T183 | Clutch Disc Alignment Tool (Spline count = 10; Pilot diameter = 14.9 mm; Spline diameter = 28.6 mm), Fits BMW M42, M44, M50, S50, S52, M60, M62 engines with 15mm ID pilot bearings only NOTE: applies to models without self-adjusting clutch [More Info] | $8.45 | |
| Install Tool for Self Adjusting Clutches |
| This tool is used as a flywheel pilot bearing guide during removal of the shipping plate. |
|
| CT-1011-M37 | Clutch Installation Tool, for Self Adjusting Clutches ONLY, E39: 528i/it (from 09/97), 525i/it, 530i (through 5/03) [More Info] |  |
| $16.25 | |
Lug Nut Soft Socket |
| This special thin walled, heavy duty IMPACT socket with a riveted Aluminum insert was developed for the crucial task of R&R of wheel lugs nuts/bolts without marring or scuffing the surface of the wheel or bolts. Measuring at 3.5" to fit into deep recess of wide wheels. Comes with a limited life-time warranty, guaranteed to be the last 17mm wheel lug socket you'll ever buy. |
|
PEL-TOL-LUG17MM | Impact Duty Soft-Walled Lug Nut Socket - 17mm, 1/2 inch drive [More Info] | $29.40 | |
These Chrome Molybdenum thin walled sockets have a plastic outer sleeve to prevent wheel damage during removal and installation of wheel fasteners. Each socket also has a durable plastic inset to help protect the nut head (note that the plastic insert does not protect the sides of the nut). This set includes color coded 17mm, 19mm, and 21mm protective sockets in a custom blow molded case. These sockets are 1/2" drive will help keep your wheels looking new.
NOTE: These are IMPACT-duty sockets for use with either impact or hand drivers. |
|
SCHW-PPS-1721 | Protecta Socket Set (17mm, 19mm, 21mm), 1/2 inch drive [More Info] | $19.00 | |
Lug Nut Torque Socket Set |
Take the guess work out of tightening your wheels, these Schwaben torque sockets will stop tightening when the appropiate torque has been reached. This handy color coded set includes 17mm, 19mm, and 21mm sockets in a compact blow molded case. Sockets are 1/2" drive and are preset for 100Nm (74ft-lbs)
NOTE: These are for use with hand drivers only - they are NOT suitable for impact guns. |
|
SCHW-PTS-12-1721 | Torque Socket Set (17mm, 19mm, 21mm), 1/2 inch drive [More Info] | $51.95 | |
Suspension Tools |
| You can never perform a good job on repairing your BMW if you don't have the right tool. A lot of people try to cut corners because they either don't have the tool they need, or they don't even know that it exists! Having the right tool for the job saves time, money, and wasted effort. A job that can take 4 hours without the right tool, can take a mere few minutes. You're already saving lots of money by doing the work yourself, spend some money and get the tool that you need. Once it's in your collection, you will not know how you got along without it! |
|
