| BMW E36 Exhaust Pipes - Page 3 |
Exhaust Hardware |
| Support Brackets |
18-21-1-723-410-M9 | Exhaust Support Bracket, Rear Muffler to Rubber Mount, Lower Part, E36 (2 per car, sold per each)
Brand: Genuine BMW [Photo] |  |
| $1.75 |  |
18-21-1-723-555-M25 | Exhaust Support Bracket, Rear Muffler to Rubber Mount, "Upper Part", (2 per car, sold per each), E36 325i/iC/is, 318i/is/iC/ti, 323is/iC, 328i/is/iC
Brand: Eberspaecher [Photo] | |
| $4.25 | |
18-20-1-402-479-M9 | Exhaust Support Bracket, Rear Muffler to Rubber Mount, "Upper Part" (2 per car, sold per each), E36 M3 B30/B32
Brand: Genuine BMW [Photo] | |
| $17.00 | |
18-30-1-737-975-BOE | Exhaust Support, E36 318i/is/ti Manual Trans (up to 12/96)
Brand: Genuine BMW [Photo] | $13.00 | |
Exhaust Manifolds |
| Cracked exhaust manifolds have plagued the E36 models through the years. The manifolds installed on these cars are made of cast alloy steel. This alloy is heavy and durable, but over the years, it can become increasingly susceptible to cracks. Its not uncommon to discover a loud exhaust leak coming from the engine compartment. If its not a worn-out exhaust gasket, its most likely a cracked manifold. A cracked manifold will introduce an exhaust leak into the system. Besides making the engine noisy, it can cause the engine to run roughly and erratically. |
|
| 11-62-1-728-370-BOE | Exhaust Manifold, 318i/is/iC/ti (1992-08/96)
Brand: Genuine BMW | $350.75 | |
| 11-62-1-433-967-BOE | Exhaust Manifold, 318i/is/iC/ti (01/97-1999)
Brand: Genuine BMW | $350.75 | |
| 11-62-1-716-736-BOE | Exhaust Manifold, Front, 325i/is/iC (1992-95), M3 w/ 3.0 (1995)
Brand: Genuine BMW | $328.50 | |
| 11-62-1-716-733-BOE | Exhaust Manifold, Rear, 325i/is/iC (1992-95), M3 w/ 3.0 (1995)
Brand: Genuine BMW | $328.50 | |
| 11-62-1-744-250-BOE | Exhaust Manifold, Front, 323i/iC (1996-99), 328i/is/iC (1996-99), M3 w/ 3.2 (1996-99)
Brand: Genuine BMW | $328.50 | |
| 11-62-1-744-251-BOE | Exhaust Manifold, Rear, 323i/iC (1996-99), 328i/is/iC (1996-99), M3 w/ 3.2 (1996-99)
Brand: Genuine BMW | $328.50 | |
Air/Fuel Ratio Monitors  |
The K&N Air/Fuel Monitor is designed to help the performance enthusiast calibrate and fine tune the air/fuel mixture ratio. It is an invaluable diagnostic tool that has a place in everyone's tool box, or you can install it in your car to give you real-time readings. This kit continually monitors an engine's air/fuel ratio while the engine is running. It is extremely sensitive to air/fuel ratio changes and will show them instantly and accurately, within the range of the oxygen sensor.
The instrument works whether the engine is carbureted or fuel injected, normally aspirated, turbocharged, or supercharged, and at any load condition. This precision instrument also works with nitrous oxide, but will not work with diesel or nitromethane fuels. This kit comes complete with an oxygen sensor that must be installed into the exhaust system by welding. If your BMW is already equipped with an oxygen sensor an air/fuel monitor may be purchased separately and wired into the existing electrical system. An oxygen sensor is also available separately.
Vehicles with dual exhaust systems can utilize an oxygen sensor in each headpipe or collector that is controlled by a switch that will allow each sensor or bank of cylinders to be read independently. This can show if there is a fuel distribution problem within the intake system, or help to pinpoint a potential problem in advance. |
|
PEL-SW85-2437 | Rectangle Surface mount Air/Fuel Ratio Monitor Kit, w/oxygen sensor [Photo] | $199.55 | |
PEL-SW85-2441 | Round In Dash mount Air/Fuel Ratio Monitor Kit, w/oxygen sensor [Photo] | $256.95 | |
PEL-SW85-2439 | Rectangle Surface mount Air/Fuel Ratio Monitor Kit, without oxygen sensor [Photo] | $188.35 | |
PEL-SW85-2442 | Round In Dash mount Air/Fuel Ratio Monitor Kit, without oxygen sensor [Photo] | $217.40 | |
PEL-SW85-2438 | Replacement Oxygen Sensor [Photo] | $85.00 | |
PEL-SW85-2440 | O2 Sensor Plug and Fitting [Photo] | $21.60 | |
| PEL-SW85-21688 | Weld on Fitting | $14.50 | |
PEL-SW85-21686 | O2 Sensor Plug [Photo] | $16.15 | |
Anti-Seize Lubricant |
| Using a quality anti-seize lubricant now can save you hours of pain-staking work the next time you attempt to remove that old hardware. These premium compounds offer high temperature resistance, corrosion protection, and good electrical conductivity. |
|
2012-M19 | Liqui Moly Anti-seize Compound, 100g [Photo] | |
| $9.00 | |
WRTH-8938132 | Wurth CU 1100 Copper Paste, 1 lb [Photo] | $25.00 | |
