| BMW E34 Tools - Page 6 |
Transmission Tools |
| Transmission Drain Plug Socket |
| This special 17mm ID socket is used to remove the transmission fill and drain plugs. This tool is essential when doing any transmission service. Please be sure to check first if your transmission uses this type and size of plug before ordering. |
|
PEL-DPR-1017 | Transmission Drain Plug Socket, BMW Models with 17mm allen plugs ONLY, Each [More Info] | $28.50 |  |
| Transmission/Differential Oil Seal Arbors |
| These oil seal arbors are used to properly install the oil seals on the transmission and differential output shafts. |
|
PEL-TOL-3020 | Transmission Oil Seal Arbor For Getrag Transmissions, Check Plate on Transmission for Model Number, All Getrag G242/262/G240 and 260 transmissions, Each 21.00 [More Info] | $35.30 | |
PEL-TOL-3000 | Differential Oil Seal Arbor, BMW All E23, E24, E28, E30 E32 And E34 Models, Each [More Info] | No Longer Available | |
Clutch Tools |
| You can never perform a good job on repairing your BMW if you don't have the right tool. A lot of people try to cut corners because they either don't have the tool they need, or they don't even know that it exists! Having the right tool for the job saves time, money, and wasted effort. A job that can take 4 hours without the right tool, can take a mere few minutes. You're already saving lots of money by doing the work yourself, spend some money and get the tool that you need. Once it's in your collection, you will not know how you got along without it! |
|
| Torx Female Socket Set |
| These odd-shaped sockets are required to remove some of the bolts that connect the engine to the transmission. Seven sizes E-6 through E-16. The three smaller sizes are 1/4" drive; the four larger sizes are 3/8" drive. Made of heat-treated alloy steel. Sockets are kept in a convenient vinyl holder. Includes External Torx Sockets: E6, E7, E8, E10, E12, E14, and E16. |
|
TOL-LIS26750 | Torx Female Socket Set [More Info] | $20.23 | |
| Flywheel Bolt Tool, Special T60 Torx Socket |
| This T60 Torx Socket is essential in order to R&R dual mass flywheel bolts of ZMS engines. The bolts are situated off-center to their respective access points. The slimmed-down shaft allows for the socket to line up straight with the bolt. |
|
TOL-BMW3048 | Flywheel Bolt Tool, Special T60 Torx Socket, fits E34 and E39 4.0L and 4.4L V-8s [More Info] | $42.95 | |
| Clutch Wear Gauge |
| This tool allows you to check the thickness of the clutch disc without having to remove the transmission (BMW Service Tool# 21 2 060). Information on how to use the tool is located on page 3 of this BMW factory manual. |
|
PEL-TOL-3004 | Clutch Wear Gauge, Fits M10, M20, M30, S14 S38 Engines ONLY [More Info] | $23.50 | |
| Pilot Bearing Puller |
| Designed to extract bearings and bushings with an I.D. of 12mm up to 15mm. |
|
PEL-TOL-1088 | Pilot Bearing Puller, BMW All Models, Each [More Info] | $52.90 | |
| Clutch Alignment Tools |
PEL-TOL-T183 | Clutch Disc Alignment Tool (Spline count = 10; Pilot diameter = 14.9 mm; Spline diameter = 28.6 mm), Fits BMW M42, M44, M50, S50, S52, M60, M62 engines with 15mm ID pilot bearings only [More Info] | $8.45 | |
| Mityvac Brake Bleeder Kit |
| Tired of sucking up bad tasting brake fluid? Tired of bleeding your brakes using the old fashioned method of bribing a family member to stomp on the pedal? Try a vacuum bleeder. This system sucks fluid through the brake lines and eliminates all air bubbles from a normal system. Also very useful is our Pelican Technical Article on Bleeding Porsche Brakes. |
|
MTVC-001 | Mityvac Brake Bleeder Kit [More Info] | $36.95 | |
