| BMW E30 Fuel System - Page 3 |
Fuel Injectors |
| Fuel Injector Seals/Clips |
| These are required to maintain a good seal from the injector to the manifold. |
|
13-64-1-730-767-M213 | Fuel Injector Seal (7.8 x 3.6mm), BMW E30 3 Series, 2 seals per injector, sold per each
Brand: D P H [Photo] [Photo] |  |
| $1.00 |  |
13-53-1-274-729-M9 | Securing Clip for Fuel Injector, BMW E30 3 Series, As Needed, Each
Brand: Genuine BMW [Photo] [Photo] | |
| $1.00 | |
Cold Start Valves |
| The Cold Start Valve acts as an extra fuel injector, providing the engine with extra fuel when cold. In theory, it works the same way as a choke on a carburetor, intentionally making the engine run rich until it has warmed up to operating temperature. Usually, when a cold start valve starts to go bad or leak, you will notice poor fuel economy and hard starting when the engine is hot. |
|
13-64-1-285-087-M14 | | $164.00 | |
13-64-1-273-278-M9 | Cold Start Injector, 325/e/es (1984-87), 325iX (1987-91)
Brand: Genuine BMW [Photo] [Photo] | |
| $185.00 | |
| Cold Start Valve O-Rings |
11-61-1-254-062-M213 | O-Ring for Cold Start Injector, 318i (1984-85)
Brand: D P H [Photo] | |
| $0.25 | |
11-61-1-254-062-M213 | O-Ring for Cold Start Injector, 325/e/es (1984-87), 325iX (1987-90)
Brand: D P H [Photo] | |
| $0.25 | |
Fuel Pressure Regulators  |
| Make sure that your fuel injection system is running properly and at the correct fuel pressure. Changes in the fuel pressure can affect the power and performance of the engine and can be potentially dangerous. Most pressure regulators are quite simple in design, A small valve inside of the regulator allows fuel pressure to build up to the amount needed for the fuel injection system to work properly. If too much pressure is in the line, the valve automatically opens and bleeds off the increased pressure, thus keeping your fuel pressure within operating tolerances. If the unit goes bad, It can cause the pressure in the fuel lines to increase or decrease, possibly causing a dangerous situation. |
|
13-53-1-722-040-M14 | Fuel Pressure Regulator, 3.0 Bar, 318i (1984-85), 325i/is/iC/iX (1987-91), M3 (1987-91)
Brand: Bosch [Photo] [Photo] | |
| $79.75 | |
13-53-1-722-039-M14 | Fuel Pressure Regulator, 2.5 Bar, 325/e/es (1984-86)
Brand: Bosch [Photo] [Photo] | |
| $79.50 | |
13-53-1-743-378-M14 | Fuel Pressure Regulator, 3.0 Bar, 318i/is/iC (1991)
Brand: Bosch [Photo] | |
| $88.50 | |
Fuel Tank and Related Parts |
| Has your fuel tank rusted through? Annoying fuel vapors stinking up your car? We can provide you with the correct parts for your E30 BMW and fix a potentially hazardous situation. |
|
| Fuel Tanks |
| 16-11-1-177-983-BOE | Fuel Tank, 318i (1984-85), 318i/is/iC (1991), 325/e/es/i/is/ic/iX (1984-91), M3 (1987-91)
Brand: Genuine BMW | $485.75 | |
| Fuel Tank Sending Units |
16-14-1-152-266-M82 | Fuel Tank Sending Unit, 318i (1984-86), 318i/is/iC (1991), 325i/is/iX (1987-92), M3 (1987-91)
Brand: VDO [Photo] | |
| $92.25 | |
16-14-1-179-720-M82 | Fuel Tank Sending Unit (Left Side of Tank), 325i/is/iC/iX (09/87-92)
Brand: VDO [Photo] | |
| $92.25 | |
| Fuel Tank Seals |
16-11-1-744-369-M9 | Sealing Ring for Fuel Tank Suction Device, 318i (1984-86), 318i/is/iC (1991), 325/e/es/i/is/iX (1987-91), M3 (1987-91)
Brand: Genuine BMW [Photo] | |
| $1.75 | |
16-12-1-150-391-M9 | Sealing Ring for Fuel Tank Sending Unit, E30 318i, 318i M42, 325/e/es, 325i/is (from 9/87), M3
Brand: Genuine BMW [Photo] | |
| $6.75 | |
