| BMW E28 Suspension Tools & Books - Page 1 |
Alignment Tools  |
| Whether your simply doing your own work, or trying to tune your car up for the track, our offering of special alignment tools will help you to find the absolute best setup for your BMW. |
|
| Precision Camber Alignment Tool |
The SmartCamber tool digitally measures camber and caster quickly, easily, and repeatedly. With the push of a button it automatically compensates for non-level floors so it can be used at home, at the track...even on a trailer with complete confidence. Plus, the module is removable and can be used for measuring any angles including drive shaft, wing and suspension angles, so it is really two tools in one. Accurately measures in 1/10th of a degree increments. Most effectively used with the optional Hands-Free adapter (as shown in second photo) because it allows the tool to be attached to the wheel while suspension adjustments are made - fast, accurate and super easy. Beats the heck out of using an $18,000 alignment rack!
Optional Wooden Carrying Case: Hand made lacquered birch plywood box with specially designed anchor screws to hold the tool in place. Very high quality and made in up-state New York by skilled craftsmen. |
|
PEL-SR1030 | SmartCamber Alignment Tool (12in to 18in wheels) [Photo] | $245.95 |  |
PEL-SR1040 | SmartCamber Alignment Tool with Handsfree Adapter [Photo] | $316.95 | |
PEL-SR1001 | Wooden Carrying Case for SmartCamber Alignment Tool [Photo] | No Longer Available | |
| Laser Toe-in Alignment Plates |
| People have been asking for an affordable, yet highly accurate toe measuring tool for years. Finally, someone came up with an idea that is based on the original "toe plates" method, where two plates that lean against the tire and then, with a tape measure, toe is measured. It is a system that is better than nothing, but has real limitations. For example, body and suspension parts are always in the way making accurate measuring troublesome and inaccurate. With the new Laser Toe Plates, the same principle is applied, but an extremely precise laser beam is shot just 14mm above the ground, reflecting back to a target. With an adjusting knob, the laser is guided to the target and once hit, you simply read the dial indicator (its readings are in minutes of a degree; a handy conversion chart for minutes to decimal is included). It also tells you if you have toe-in or toe-out. Completely portable and extremely accurate. |
|
PEL-SR4522 | Laser Toe-in Alignment Plates [Photo] | $581.45 | |
| Precision Ride Height Gauge |
This ride height gauge was designed to be used on a wide variety of cars, from very low super-speedway cars to sports cars to vintage cars to daily drivers. Its function is simple and straightforward and easy to use. When not in use or in transport, there is a sliding black plastic bushing that locks the arm in place, this will prevent the arm from bouncing and damaging the arm or the indicator.
Measuring Range: As delivered, the gauge will read from .75" to 3.0". With the enclosed long standoffs, the range is increased from 2.75" to 5.0". The gauge is calibrated so the initial reading you see on the dial indicator is the thickness from the bottom of the tool to the top of the sensing nut (acorn nut). It will read directly in thousands of an inch. One full revolution of the large needle equals one inch. The smaller indicator reads in full inches. The Gauge's measuring arm is a full 18" long and only .75" tall, so it can get under the lowest of cars. |
|
PEL-SR1050 | Precision Ride Height Gauge [Photo] | No Longer Available | |
Suspension Tools |
| You can never perform a good job on repairing your BMW if you don't have the right tool. A lot of people try to cut corners because they either don't have the tool they need, or they don't even know that it exists! Having the right tool for the job saves time, money, and wasted effort. A job that can take 4 hours without the right tool, can take a mere few minutes. You're already saving lots of money by doing the work yourself, spend some money and get the tool that you need. Once it's in your collection, you will not know how you got along without it! |
|
| CV Joint Removal Tool |
| Use our extra long allen socket removal tool to easily remove those pesky CV joint bolts without damaging your Axle boots. Avoid stripping your bolts, and spending wasted hours of cutting and grinding stripped bolts. 3/8 inch drive. |
|
PEL-TOL-P243 | CV Joint Removal Tool, BMW All [Photo] | $31.00 | |
| Front Wheel Hub/Bearing Nut Socket |
83-30-0-491-896-BOE | Front Wheel Hub/Bearing Nut Socket - 46mm, 3/4 in. Drive, BMW Tool #31-2-080, fits E23, E24, E28, E32, E34, E36, E38, E46 [Photo] | $64.50 | |
| Rear Wheel Bearing Extractor and Installer Kit |
| If you want to save on a costly repair, replace your own bearing or pull your own hubs with our all in one master kit. Designed to efficiently remove and install hub and wheel bearings, this kit will make the notoriously difficult job of removing rear wheel bearings a breeze. The tool eliminates the need for such drastic measures such as a slide hammer or flame torch to remove the rear wheel bearing. The tool facilitates the installation and removal of the rear bearings, and makes the whole job 1000% easier. |
|
| PEL-TOL-SIRB90-B1 | Hub/Bearing Extractor and Installer Kit, E28 5-Series (524td, 528, 533, 535, M5) | $229.00 | |
| Bushing Adapter Kit |
| No need to disassemble the whole rear end in order to use a hydraulic press with this tool. Designed to work in conjunction with a C-clamp. This kit is used for removal and installation of the rear A-arm metal clad support bushings. |
|
PEL-TOL-3027 | Bushing Adapter Kit, BMW E28 5-Series (all) [Photo] | $44.50 | |
