|  | | | BMW E28 Axles & Bearings - Page 1 | CV Joints and Related Parts | | CV Joints are responsible for providing a direct link between the axles and the wheels. They allow the power to be distributed evenly throughout varying degrees of rotation. Without them, you wouldn't be able to have suspension in the rear. We here at Pelican offer all the parts needed to replace or repair your BMW's CV Joints. |
| | CV Boot Kits | 
33-21-9-067-906-M60 | Axle Boot Kit for Inner/Outer C/V Joint, 2 Kits Per Axle Shaft, BMW E28 5 Series, All, Each
Brand: Loebro [Photo] |  |
| $15.25 |  | | Axle Nuts | 
33-41-1-123-428-M9 | Axle Nut, 2 Per Car, BMW E28 5 Series, All, Each
Brand: Genuine BMW [Photo] | |
| $9.75 | | 
33-41-1-123-973-M9 | Axle Nut Lock Plate, BMW E28 5 Series, All, Each
Brand: Genuine BMW [Photo] | |
| $1.50 | | Wheel Bearings & Hub Parts | 
31-21-1-468-753-M34 | Front Wheel Hub with Bearing for Cars with or without ABS, (2 per car, sold per each) NOTE: Also use one 31-21-1-128-423-M9 Inner Seal, E28 524td, 528e, 535i/is, M5
Brand: FAG [Photo] | |
| $129.00 | | 
31-21-1-128-423-M9 | Front Wheel Inner Dust Shield (2 per car, sold per each), E28 524td, 528e, 535i/is, M5
Brand: Genuine BMW [Photo] | |
| $2.50 | | 
33-41-1-468-903-M34 | Rear Wheel Bearing 42 x 80 x 42, E28 524td, 528e, 533i, 535i/is, M5, 2 per car sold per each
Brand: FAG [Photo] | |
| $37.25 | | 
31-21-1-128-336-M36 | Front Wheel Hub Nut, E28 524td, 528e, 533i, 535i/is, M5, Each
Brand: Febi [Photo] | |
| $8.25 | | CV Joint Grease  | | Remember to lube and pack your CV joints when you replace them. Pelican carries both the LubroMoly and the Swepco 101 grease for complete lubrication of your joints. Both are very good and very slippery. Each contains enough grease to effectively one CV joint from completely dry. |
| | Swepco CV Joint Grease | 
SWE-101 | Swepco CV Joint Grease, 14.4 oz [Photo] | $10.30 | | | OE Lubromoly CV Joint Grease | | 3510-M19 | CV Joint Grease, 100g tube
Brand: Liqui Moly [Photo] | |
| $5.25 | | | CV Joint Removal Tool | Avoid stripping your bolt heads and spending wasted hours cutting and grinding them off by using this special tool to easily remove those pesky CV joint bolts. This tool is for use with 12-point star-shaped bolts only. Please make sure to check your bolts before ordering. It's common for previous owners to replace the 12-point star shaped bolts with more standard allen head bolts instead. Although the 12-point pattern allows you to get a better grip on the bolts (with the correct tool), and apply the high torque that the bolts require, previous owners may have stripped out these bolt heads by attempting to use a torx or hex driver instead of the proper tool. A word of caution here - these other tools MAY work, but if they strip the bolt head, then you are in for an entire afternoon of grinding it off the next time it's replaced.
TIP: Spray the bolts down with WD-40 or Liquid Wrench first to loosen the dirt and debris in the bolt head, then scrape out any dirt that may be left. With the socket on a 6" extension, slip the tool into the bolt head and give it a gentle rap on the end with a mallet to seat it firmly. Following this simple procedure will hopefully avoid you from stripping any CV bolts. |
| 
TOL-SK45438 | CV Joint Bolt Removal Tool - 8mm, 12-point Socket Driver, 3/8 in. drive [Photo] [Photo] | $12.75 | |
| |
|
|
|
