In many ways, tire mechanics is an unpleasant topic. It is shrouded in
uncertainty, controversy, and trade secrecy. Both theoretical and experimental studies are
extremely difficult and expensive. It is probably the most uncontrollable variable in
racing today. As such, it is the source of many highs and lows. An improvement in modeling
or design, even if it is found by lucky accident, can lead to several years of domination
by one tire company, as with BFGoodrich in autocrossing now. An unfortunate choice of tire
by a competitor can lead to frustration and a disastrous hole in the budget. This
month, we investigate the physics of tire adhesion a little more deeply than in the past.
In Parts 2, 4, and 7, we used the simple friction model given by , where is the maximum traction force available from
a tire; , assumed
constant, is the coefficient of friction; and is the instantaneous vertical load, or
weight, on a tire. While this model is adequate for a rough, intuitive feel for tire
behavior, it is grossly inadequate for quantitative use, say, for the computer program we
began in Part 8 or for race car engineering and set up.
I am not a tire engineer. As always, I try to give a fresh look at any topic from a
physicist's point of view. I may write things that are heretical or even wrong, especially
on such a difficult topic as tire mechanics. I invite debate and corrections from those
more knowledgeable than I. Such interaction is part of the fun of these articles for me.
I call this month's topic `grip angle.' The grip angle is a quantity that captures, for
many purposes, the complex and subtle mechanics of a tire. Most writers call this quantity
`slip angle.' I think this name is misleading because it suggests that a tire works by
slipping and sliding. The truth is more complicated. Near maximum loads, the contact patch
is partly gripping and partly slipping. The maximum net force a tire can yield occurs at
the threshold where the tire is still gripping but is just about to give way to total
slipping. Also, I have some difficulties with the analyses of slip angle in the
literature. I will present these difficulties in these articles, unfortunately, probably
without resolution. For these reasons, I give the quantity a new name.
A tire is an elastic or deformable body. It delivers forces to the car by stretching,
compressing, and twisting. It is thus a very complex sort of spring with several different
ways, or modes, of deformation. The hypothetical tire implied by with constant would be a nonelastic
tire. Anyone who has driven hard tires on ice knows that nonelastic tires are basically
uncontrollable, not just because is small but because regular tires on ice do
not twist appreciably.
The first and most obvious mode of deformation
is radial. This deformation is along
the radius of the tire, the line from the center to the tread. It is easily visible as a
bulge in the sidewall near the contact patch, where the tire touches the ground. Thus,
radial compression varies around the circumference.
Second is circumferential deformation. This is most easily visble as wrinkling of the
sidewalls of drag tires. These tires are intentionally set up to deform dramatically in
the circumferential direction.
Third is axial deformation. This is a deflection that tends to pull the tire off the
(nonelastic) wheel or rim.
Last, and most important for cornering, is torsional deformation. This is a
difference in axial deflection from the front to the back of the contact patch.
Fundamentally, radial, circumferential, and axial deformation furnish a complete
description of a tire. But it is very useful to consider the differences in these
deflections around the circumference.
Let us examine exactly how a tire delivers cornering force to the car. We can get a
good intuition into the physics with a pencil eraser. Get a block eraser, of the
rectangular kind like `Pink Pearl' or `Magic Rub.' Stand it up on a table or desk and
think of it as a little segment of the circumference of a tire. Think of the part touching
the desk as the contact patch. Grab the top of the eraser and think of your hand as the
wheel or rim, which is going to push, pull, and twist on the segment of tire circumference
as we go along the following analysis.
Consider a car traveling at speed in a straight line. Let us turn the steering
wheel slightly to the right (twist the top of the eraser to the right). At the instant we
begin turning, the rim (your hand on the eraser), at a circumferential position just
behind the contact patch, pushes slightly leftward on the bead of the tire. Just ahead of
the contact patch, likewise, the rim pulls the bead a little to the right. The push and
pull together are called a force couple. This couple delivers a
torsional,
clockwise stress to the inner part of the tire carcass, near the bead. This stress is
communicated to the contact patch by the elastic material in the sidewalls (or the main
body of the eraser). As a result of turning the steering wheel, therefore, the rim twists
the contact patch clockwise.
The car is still going straight, just for an instant. How are we going to explain a net
rightward force from the road on the contact patch? This net force must be there,
otherwise the tire and the car would continue in a straight line by Newton's First Law.
Consider the piece of road just under the contact patch at the instant the turn begins.
The rubber particles on the left side of the patch are going a little bit faster with
respect to the road than the rest of the car and the rubber particles on the right side of
the patch are going a little bit slower than the rest of the car. As a result, the left
side of the patch grips a little bit less than the right. The rubber particles on the left
are more likely to slide and the ones on the right are more likely to grip. Thus, the left
edge of the patch `walks' a little bit upward, resulting in a net clockwise twisting
motion of the patch. The torsional stress becomes a torsional motion. As this motion is
repeated from one instant to the next, the tire (and the eraserI hope you are still
following along with the eraser) walks continuously to the right.
The better grip on the right hand side of the contact patch adds up to a net rightward
force on the tire, which is transmitted back through the sidewall to the car. The chassis
of the car begins to yaw to the right, changing the direction of the rear wheels. A
torsional stress on the rear contact patches results, and the rear tires commence a
similar `walking' motion.
The wheel (your hand) is twisted more away from the direction of the car than is the
contact patch. The angular difference between the direction the wheel is pointed and the
direction the tire walks is the grip angle. All quantities of interest in tire
mechanicsforces, friction coefficients, etc., are conventionally expressed as
functions of grip angle.
In steady state cornering, as in sweepers, an understeering car has larger grip angles
in front, and an oversteering car has larger grip angles in the rear. How to control grip
angles statically with wheel alignment and dynamically with fourwheel steering are
subjects for later treatment.
The greater the grip angle, the larger the cornering force becomes, up to a point.
After this point, greater grip angle delivers less force. This point is analogous to the
idealized adhesive limit mentioned earlier in this series. Thus, a real tire behaves
qualitatively like an ideal tire, which grips until the adhesive limit is exceeded and then slides. A real
tire, however, grips gradually better as cornering force increases, and then grips
gradually worse as the limit is exceeded.
The walking motion of the contact patch is not entirely smooth, or in
other words,
somewhat discrete. Individual blocks of rubber alternately grip and slide at high
frequency, thousands of times per second. Under hard cornering, the rubber blocks
vibrating on the road make an audible squaling sound. Beyond the adhesive limit, squealing
becomes a lower frequency sound, `squalling,' as the point of optimum efficiency of the
walking process is bypassed.
There is a lot more to say on this subject, and I admit that my first attempts at a
mathematical analysis of grip angle and contact patch mechanics got bogged down. However,
I think we now have an intuitive, conceptual basis for better modeling in the future.
Speaking of the future, summarize briefly the past of and plans for the Physics of
Racing series. The following overlapping threads run through it:
 Tire Physics
 concerns adhesion, grip angle, and elastic modeling. This has been covered in Parts 2,
4, 7, and 10, and will be covered in several later parts.
 Car Dynamics
 concerns handling, suspension movement, and motion of a car around a course; has been
covered in Parts 1, 4, 5, and 8 and will continue.
 Drive Line Physics
 concerns modeling of engine performance and acceleration. Has been covered in Parts 3,
6, and 9 and will also continue.
 Computer Simulation
 concerns the design of a working program that captures all the physics. This is the
ultimate goal of the series. It was begun in Part 8 and will eventually dominate
discussion.
The following is a list of articles that have appeared so far:
 1. Weight Transfer

 2. Keeping Your Tires Stuck to the Ground

 3. Basic Calculations

 4. There is No Such Thing as Centrifugal Force

 5. Introduction to the Racing Line

 6. Speed and Horsepower

 7. The Circle of Traction

 8. Simulating Car Dynamics with a Computer Program

 9. Straights

 10. Grip Angle

and the following is a tentative list of articles I have planned for the near
future (naturally, this list is `subject to change without notice'):
 Springs and Dampers,
 presenting a detailed model of suspension movement (suggested by Bob
Mosso)
 Transients,
 presenting the dynamics of entering and leaving corners, chicanes, and slaloms (this one
suggested by Karen Babb)
 Stability,
 explaining why spins and other losses of control occur
 Smoothness,
 exploring what, exactly, is meant by smoothness
 Modeling Car Data
 in a computer program; in several articles
 Modeling Course Data
 in a computer program; also in several articles
In practice, I try to keep the lengths of articles about the same, so if a topic is
getting too long (and grip angle definitely did), I break it up in to several articles. 