| BMW E46 Suspension - Page 10 |
Suspension Tools |
| You can never perform a good job on repairing your BMW if you don't have the right tool. A lot of people try to cut corners because they either don't have the tool they need, or they don't even know that it exists! Having the right tool for the job saves time, money, and wasted effort. A job that can take 4 hours without the right tool, can take a mere few minutes. You're already saving lots of money by doing the work yourself, spend some money and get the tool that you need. Once it's in your collection, you will not know how you got along without it! |
|
| Bushing Master Kit |
| No need to disassemble the whole rear end in order to use a hydraulic press with this tool. Designed for "On the Car Application" . This kit is needed for the proper R&R of the metal-clad rubber mount bushings of the rear axle carrier sub frame. Incorporating a thrust bearing to ease the pulling/pushing action, reduces the wear and tear of the tool, ensuring longevity. This Bushing Master Kit comes complete with all the proper components to efficiently get the job done right. Comes equipped with a 14mm threaded rod and press nut. |
|
PEL-TOL-3026 | Bushing Master Kit, BMW E46 3 Series, All [More Info] | $394.00 |  |
| Rear Wheel Bearing Extractor and Installer Kit |
| If you want to save on a costly repair, replace your own bearing or pull your own hubs with our all in one master kit. Designed to efficiently remove and install hub and wheel bearings, this kit will make the notoriously difficult job of removing rear wheel bearings a breeze. The tool eliminates the need for such drastic measures such as a slide hammer or flame torch to remove the rear wheel bearing. The tool facilitates the installation and removal of the rear bearings, and makes the whole job 1000% easier. |
|
| PEL-TOL-SIRB90-B2 | Hub/Bearing Extractor and Installer Kit, E46 320, 323, 325 (except Xi), 328 [More Info] | $269.00 | |
| Rear Trailing Arm Master Kit |
Combines 3 OE Tools for On the Car Removal and Installation of the 3 Bushings Located in the Main Rear Trailing Arms. Includes Case. (See below for Specific Bushings and Models)
Bushing (A) 33-32-6-771-828 Lower, outer Bushing
Bushing (B) 33-32-6-770-786 Front of Trailing Arm
Bushing (C) 33-32-6-775-551 Upper, outer Bushing
Applications
E46 Models = 323, 325, 328, 330, (Except xi Models)
Please Call or email Us if you have an X3, Z4, M3 or Xi Model. |
|
TOL-BMW3065 | Rear Trailing Arm Master Kit, Includes Case [More Info] | $414.95 | |
| Press Arbor Kit/Outer Ball Joint |
| Designed for the proper removal and installation of the outer ball joints. Comes complete with all the components to perfectly mate up to the factory ball joints. Must be used in conjunction with a hydraulic press. |
|
PEL-TOL-3038 | Press Arbor Kit, BMW E46 3 Series, All [More Info] | $175.60 | |
| Press Arbor Kit/Inner Ball Joint |
| Designed for the proper removal and installation of the inner ball joints. Used in conjunction with a hydraulic press, or on the car application when used in conjunction with a C-Clamp. |
|
PEL-TOL-3028 | Press Arbor Kit, BMW E46 3 Series, All [More Info] | $153.70 | |
| Separator |
| Designed for the proper disassembly of the pitman arm type tie rod ends w/o tearing the ball joint boots. |
|
PEL-TOL-266H | Separator, Universal, 18mm opening [More Info] | $46.20 | |
| Heavy Duty Separator |
| Designed for the proper disassembly of ball joints on drag links and tie rods. Base of opening is 21.5mm |
|
PEL-TOL-3029 | Heavy Duty Separator, Universal, 21.5mm opening [More Info] | $83.10 | |
| Heavy Duty Extractor |
| Designed for the proper disassembly of ball joints from lower wishbone. Base of opening is 25.5mm |
|
PEL-TOL-3030 | Heavy Duty Separator, Universal, 25.5mm opening [More Info] | $92.40 | |
