Order Online or Call:  
888-280-7799  
HACKER SAFE certified sites prevent over 99.9% of hacker crime.
  Search our site:   

View Cart  | Project List | Order Status |  Help    

 
- Back to Catalog -
Axle Carriers and Related Parts
Axle Hubs and Related Parts
Axle/Wheel Hubs
Axle Nuts
Dust Shields
Axle Support Parts
Wheel Bearings
CV Joints and Related Parts
CV Joints
Complete CV Axle Assemblies
CV Joint Boot Kits
CV Joint Grease
Swepco CV Joint Grease
OE Lubromoly CV Joint Grease
CV Joint Removal Tool
Axle Shafts
Axle Shafts
- Back to Catalog -
Home >  BMW CatalogE30 (1983-1991)Suspension >   BMW E30 Axles & Bearings  
BMW E30 Axles & Bearings - Page 3

CV Joint Grease    Camera Pic

Remember to lube and pack your CV joints when you replace them. Pelican carries both the LubroMoly and the Swepco 101 grease for complete lubrication of your joints. Both are very good and very slippery. Each contains enough grease to effectively one CV joint from completely dry.
Swepco CV Joint Grease

SWE-101

Swepco CV Joint Grease, 14.4 oz    [Photo]

$10.30
OE Lubromoly CV Joint Grease

3510-M19

CV Joint Grease, 100g tube
   Brand: Liqui Moly    [Photo]

$5.00
CV Joint Removal Tool
Avoid stripping your bolt heads and spending wasted hours cutting and grinding them off by using this special tool to easily remove those pesky CV joint bolts. This tool is for use with 12-point star-shaped bolts only. Please make sure to check your bolts before ordering. It's common for previous owners to replace the 12-point star shaped bolts with more standard allen head bolts instead. Although the 12-point pattern allows you to get a better grip on the bolts (with the correct tool), and apply the high torque that the bolts require, previous owners may have stripped out these bolt heads by attempting to use a torx or hex driver instead of the proper tool. A word of caution here - these other tools MAY work, but if they strip the bolt head, then you are in for an entire afternoon of grinding it off the next time it's replaced.

TIP: Spray the bolts down with WD-40 or Liquid Wrench first to loosen the dirt and debris in the bolt head, then scrape out any dirt that may be left. With the socket on a 6" extension, slip the tool into the bolt head and give it a gentle rap on the end with a mallet to seat it firmly. Following this simple procedure will hopefully avoid you from stripping any CV bolts.

TOL-SK45438

CV Joint Bolt Removal Tool - 8mm, 12-point Socket Driver, 3/8 in. drive    [Photo] [Photo]

$12.75

Axle Shafts

Did that high powered burnout snap your axle shaft in two? Fear not, Pelican has your part. If you need a complete axle assembly or new CV Joint boots, Pelican has you covered.
Axle Shafts
33-21-1-226-333-BOE

Axle Shaft Assembly, Rear, Left or Right, 2 Per Car, 318i (1984-86), Each
   Brand: Genuine BMW

$443.25

33-21-1-226-901-M60

Axle Shaft Assembly, Rear, Left or Right, 2 Per Car, E30 318i M42, 318iC, 325i/is/iC, M3, Each
   Brand: Loebro  Original Equipment Manufacturer at the time of the vehicle's assembly    [Photo]

$387.50
31-60-1-226-815-BOE

Axle Shaft Assembly, Front, Left, For iX models only, 325iX (1987-91), Each
   Brand: Genuine BMW

$1149.25
31-60-1-226-816-BOE

Axle Shaft Assembly, Front, Right, For iX models only, 325iX (1987-91), Each
   Brand: Genuine BMW

$1149.25

  Page 3 of 3  <123

 

        

  Search our site:   

View Cart & CheckOut | Project List | Order Status |  Help    

 

[Home] [Customer Service] [Shopping Cart] [Project/Wish List]
  [Privacy Statement]  [Contact Us] [About Us] [Shipping]

Copyright © 2009, Pelican Parts Inc.